Filter
Top Products
12 English
Î Let off dirty water by opening the dos-
age device at the discharge hose.
Î Rinse the dirty water tank with clear wa-
ter.
Î Remove the suction hose coupling for
draining off the fresh water and hold it
over a suitable container.
ƽ Danger
Risk of injury! When loading or unloading
the machine, it may only be operated on
gradients of max. 10%. Drive slowly.
Î If you want to transport the machine on
a vehicle secure it from slipping using
belts/ ropes.
Î Remove brushes from the brush head.
ƽ Danger
Risk of injury! Before carrying out any tasks
on the machine, set the main key to "0" and
remove it. Pull out the battery plug.
Note
Suction turbine will continue to run for a
while after switch-off. Carry out mainte-
nance tasks only after the suction turbine
has come to a halt.
Î Drain and dispose of the dirty water and
the residual fresh water.
ṇ Warning
Risk of damage. Do not wash down the ap-
pliance with water and do not use aggres-
sive detergents.
Î Drain off dirty water.
Î Rinse the dirty water tank with clear wa-
ter.
Î Check the lint filter, clean if required
Î Only SP model: Remove bulk waste
container and empty it.
Î Clean the outside of the appliance with
a damp cloth which has been soaked in
mild detergent.
Î Clean the squeegee blades and the
wiping lips, check for wear and replace
if required.
Î Check the brushes for wear, replace if
required.
Î Charge battery.
Î Check battery pole for oxidation; brush
it if required and lubricate it using pole
grease. Ensure that the connection ca-
ble sits firmly.
Î Clean the seals between dirty water res-
ervoir and cover and check for tight-
ness, replace if required.
Î Check the function of the immobilizing
brake.
Î Check the acid density of the cells if the
batteries are not maintenance-free bat-
teries.
Î Clean the brush tunnel (only SP model).
Î Have the prescribed inspection carried
out by the customer service.
To ensure a reliable operation of the appli-
ance maintenance contracts can be con-
cluded with the competent Windsor sales
office.
Î Remove the squeegee tool.
Î Loosen knobs-handles.
Î Remove the plastic parts.
Î Remove the squeegee blades.
Î Insert new squeegee blades.
Î Insert the plastic parts.
Î Tighten the cross-handles.
Î Release the wing nuts.
Î Remove bearing lid.
Î Take out the brush roller, insert a new
one (pay attention to the hexagonal in-
take of the brush rollers).
Î Place bearing lid.
Î Tighten the wing nuts.
Î Repeat process on the opposite side.
Î Raise the disk brushes.
Î Turn the disk brushes by approximately
45°.
Î Remove the disk brushes at the bottom.
Î Insert the new disk brushes in reverse
sequence.
In case of danger of frost:
Î Empty the fresh and dirty water reser-
voirs.
Î Store the appliance in a frost-protected
room.
ƽ Danger
Risk of injury! Before carrying out any tasks
on the machine, set the main key to "0" and
remove it. Pull out the battery plug.
Î Drain and dispose of the dirty water and
the residual fresh water.
In case of faults that cannot be remedied
using the table below please contact the
customer service.
The operator may only replace the following
vehicle flat fuses having the following val-
ues:
– 7.5A (F1) – Control and emergency
power supply.
– 30A (F4) – Supply to stroke and acces-
sories module.
Note
Defective fuses (F2, f3) should only be re-
placed by the service center. If these fuses
are defective, then customer service center
has to check the usage conditions and the
Drain off clean water
Transport
Saber Glide 30
Maintenance and care
Maintenance schedule
After each operation
Monthly
Yearly
Maintenance Works
Maintenance contract
Replacing the squeegee blades
Replacing the brush rollers
Replacing the Disk Brushes
Frost protection
Faults
Replace fuses