Filter
Top Products
Door Arm Hookup
Tools: Needle nose pliers
Align hole in the door arm with holes in drawbar operator bracket tabs, as shown. Insert 5/16”
x 1-1/4” clevis pin, making sure hole in clevis pin is outside of second tab of drawbar operator
bracket. Insert hairpin cotter into clevis pin hole and spread hairpin cotter to secure assembly,
as shown.
Drawbar operator bracket
Drawbar operator bracket tabs
5/16”x 1-1/4”
Clevis pin
Door arm
Cotter pin
Spread cotter pin
Clevis pin
Trolley Arm Configuration
Tools: Tape measure, Level
Measure the horizontal radius of the horizontal track to determine if you have a 12” or 14” radius
horizontal track, as shown in FIG 1; if you have a low headroom door skip this step. Determine
center line of the door. Mark vertical line at this point on the header, as shown in FIG 4. Raise the
door slightly until the top section reaches the highest point of travel (high arc), as shown in FIG
2 and FIG 3 for low headroom. Using a level, mark this high arc point onto the header where it
intersects the vertical center line, as shown in FIG 4. Hold the wall bracket’s bottom edge 1/2” -
1” (room permitting) above the high arc line and centered on the vertical center line, as shown in
FIG 4. Mark the wall bracket’s mounting holes on the header wall and then refer to your garage
door operator manual for pre-drilling and securing the wall bracket to header.
Using the operator hook-up charts, refer to the referenced illustrations for correct arm hook-up
from trolley to drawbar operator bracket. For low headroom, refer to drawbar operator hook-up
chart for low headroom.
NOTE: Refer to your operator manual for specific details on how to assembly the curved and
straight arm, as shown in FIG 5 and FIG 6, and FIG 7 and FIG 8 for low headroom.
NOTE: Depending on your setup, you may or may not have to cut straight arm to accomplish
trolley settings.
Align hole in the appropriate arm with holes in drawbar operator bracket tabs, as shown in step,
Trolley Arm Hookup. Insert 5/16” x 1-1/4” clevis pin, making sure hole in clevis pin is outside of
second tab of drawbar operator bracket. Insert cotter pin into clevis pin hole and spread hairpin
cotter to ensure it will secure assembly.
DRAWBAR OPERATOR HOOK-UP CHART,STANDARD LIFT FOR 12” AND 14” RADIUS
OPERATOR MODELS TYPE OF ARM BEING USED REF. ILLUSTRATIONS
QUANTUM/CLASSIC CURVED / STRAIGHT FIG 6
LINEAR STRAIGHT / CURVED FIG 5
LIFTMASTER (SEARS) CURVED / STRAIGHT FIG 6
GENIE CURVED / STRAIGHT FIG 6 Or FIG 5
DRAWBAR OPERATOR HOOK-UP CHART FOR LOW HEADROOM
OPERATOR
MODELS
TYPE OF ARM BEING USED
PREFERRED
HOOKUP
REF. ILLUSTRA-
TIONS
OPTIONAL
HOOK-UP
REF. ILLUSTRA-
TIONS
QUANTUM /
CLSSSIC
CURVED /
STRAIGHT
FIG. 8 STRAIGHT FIG. 7
LINEAR STRAIGHT FIG. 7 N/A N/A
LIFTMASTER
(SEARS)
CURVED /
STRAIGHT
FIG. 8 STRAIGHT FIG. 7
GENIE CURVED /
STRAIGHT
FIG. 8 STRAIGHT FIG. 7
FIG 1
12” or 14”
FIG 2
Horizontal
track
Level
High arc
Top section
Horizontal
radius
High arc
FIG 4FIG 3
TorqueMaster
®
counterbalance
Vertical
center line
From step
Typical 1/2”-1”
above high arc
High arc line
Header
Top section
Low headroom track
Level
Cut straight arm to
accomplish trolley
setting
FIG 6
FIG 5
Curved arm
Curved arm
Cut straight arm to
accomplish trolley
setting
Straight arm
Straight arm
Curved arm
Straight arm
FIG 8
FIG 7
Cut straight arm to
accomplish trolley setting
Inside Lock
Tools: Power drill, 7/16” Socket driver, Tape measure
Install the inside lock on the second section of the door. Secure the lock to the section with (4)
1/4”-20 x 11/16” self drilling screws. Square the lock assembly with the door section, and align
with the square hole in the vertical track. The inside lock should be spaced approximately 1/8”
away from the section edge.
IMPORTANT: INSIDE LOCK(S) MUST BE REMOVED OR MADE INOPERATIVE IN THE UNLOCKED
POSITION IF AN OPERATOR IS INSTALLED ON THIS DOOR.
13
Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer,
refer to your local yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com
Optional Installation