10
OPERATINGINSTRUCTIONS‐continued
ControlBoardFunctions:
MODE Button:
The MODEbutton allowsyou to switch operating mode on
yourPelletStoveRoomHeater.DepresstheMODE buttontoswitchbetween
Manual and T‐STAT modes.As you depressthe MODE button the indicator
lightabovethedesiredmodewillengage.WhenyouengagetheManualmode,
youwillbe
abletomanuallyselect theheatsettings.Ifyou haveinstalle da
remote thermostatfor your PelletStove Room Heater and wish tohave the
heatercontrolledbythatthermostat,depresstheMODEbuttontoen gageT‐
STAT mode.The thermostat will control the heat output of the Heater
alternating
betweenthelowestheatlevelandthehighestheatlevelthatyou
havepre‐selected.
TheT‐STATmodeprovid esthemostevenheatoutput,forbettercomfort,and
toextendthelifeofthepelletfuelignitionsystem.Additionally,theconstant
flameservesasawarningforpeopleandpetstokeepawayfromtheheater
whileitisinoperation.
ON/OFF Button:
The ON/OFFbutton isused toturn theheateron andoff.
Whenever there is power to the heater, the LED indicator light above the
ON/OFFbuttonwillbesolidred.Iftheheateriscoldpriortostart‐up,press
andreleasetheON/OFFbutton.TheLEDlightabove
theON/OFF buttonwill
alternatelyflashredandgreentoindicatethestartup cyclehasstarted.Fuel
pelletswillstarttofeedintotheburnpotandthepelletfuelignitionsystemwill
be activated.Flames in the burn pot will normally appear between 4‐8
minutes,andoncetheflame
hasbeenestablished,thestartupcyclewillend,thistakesbetween8‐12minutes.At
thispointtheLEDindicatorlightabovetheON/OFFbuttonwillglowsolidgreen.Theuserwillnowbeableto
makeheatleveladjustments.
HEATLEVELButton:
DepresstheHEATLEVELbuttontoadvancetheheatlevelbyoneleveluntilyou reachthe
maximumsetting;fromthemaximumlevelyouwillde creaseoneleveleachtimeyoudepresstheHEATLEVEL
button. The circulation fan speed will also increase with the heat level setting.Wait until
the startup cycle is
completeandtheON/OFFLEDissolidgreentosetHeatLevel .(TheHEATLEVELLEDsarealsousedascodesto
indicateamalfunction,pleaserefertothe
SafetyFeaturesandwarningcodessectionformoreinformation.)
FANButton:
DepressingtheFANbuttonwillsetthecirculationfanspeedtohigh,overridingtheautomaticfa n
speed control.The onboard logicwill modulate thefan speedin accordancewith theheat levelsetting. It is
recommendedthatyouallowthecontroltoautomaticallysetandadjustthespeedofthe
fantoobtainoptimum
efficiencyandminimalfannoise.
AUGER Button:
Whenever Operating the Pellet Stove forFirst Time, or ifThe StoveRuns OutOf Pellets, itis
NecessarytoPrimetheAugerwithPelletFuel.Todothis,PressandHoldtheAUGERButtonforApproximately3
SecondsuntiltheAUGERLEDilluminates.ThisProcedurewillprimetheAuger
andthenAutomaticallyInitiatethe
NormalIgnitionCycle.NOTICE:Donotusethisprocedurefornormalstartup.Todosowouldcauseexcessive
fuelbuild‐upintheburnpot.
AUGER TRIM Button
: This Button is only enabled when operating at Heat Level 1. Depress the AUGER TRIM
ButtontochangetheAugerfeedrateontheminimumheatlevel;toaccount forthequalityofpellet fuelbeing
used.Increasing
Figure3