Filter
Top Products
PAGE 30 — MAYCO LS600 PUMP — OPERATION AND PARTS MANUAL — REV. #4 (9/15/11)
LS600 PUMP — OPERATION
REMOTE CONTROL (OPTIONAL)
The LS600 Concrete Pump has a remote control feature
that allows the pump to be remotely controlled. If desired,
the pump can be operated via a receiver/transmitter (radio)
or a hardwire method, which utilizes a 25-ft. extension cable.
Contact MQ Sales Department to order remote control.
Radio Remote Control
Installation of the Radio Remote Control Assembly
1. Remove the two screws on the digital control panel of
the pump. See Figure 33.
2. Tilt and slowly pull out the control panel and place on top
of box to gain access inside the box. See Figure 34.
3. Install the wireless remote module with the 2 screws
and nuts provided inside the control panel. Connect
the 3-wire connector from the wireless remote module
to the electronic control unit. See Figure 35.
Figure 33. Removing Screws from Control Panel
E
M
E
R
G
E
N
C
Y
S
T
O
P
O
F
F
O
N
I
G
N
I
T
I
O
N
R
E
M
O
T
E
C
O
N
T
R
O
L
F
L
O
W
D
I
R
E
C
T
I
O
N
V
O
L
U
M
E
L
O
C
A
L
F
O
R
WA
R
D
A
U
T
O
M
A
T
I
C
J
O
G
R
E
S
E
T
S
E
T
D
E
C
R
E
A
S
E
I
N
C
R
E
A
S
E
S
C
R
O
L
L
J
O
G
“A”
C
Y
L
I
N
D
E
R
S
T
R
O
K
E
J
O
G
“B”
R
E
V
E
R
S
E
C
E
N
T
E
R
O
F
F
R
E
M
O
T
E
S
T
A
R
T
REMOVE 2 SCREWS
CONTROL BOX
Figure 34. Pulling Out Control Panel
Figure 35. Installing Remote Control Module
SCREWSAND NUTS
WIRELESS
REMOTE
MODULE
CONNECTOR
ELECTRONIC
CONTROL
UNIT
4. Reinstall the control panel and tighten the 2 screws.
5. On the top of the unit, to the right of the control box
(Figure 36), hammer out the knock-out hole and install
the remote antenna.
6. Connect the antenna cable to the connector on the
rear of the control box (Figure 36).
Radio Remote Control Buttons Operation
The pumping operation can be performed by radio remote
control (Figure 37). Before using remote control, move the
Pumping Control Switch on the control box to the REMOTE
position. The buttons on the remote control have the following
functions.
ON/OFF - Turns the power on or off. When power is on the
power LED lights red. If the battery LED turns red, 9V battery
needs to be replaced.
E-STOP - Turns off the pump completely in an emergency.
PUMP ON/OFF - Starts and stops the forward pumping.
PUMP REV - momentarily pumps in reverse direction.
VOLUME (+) - used to increase the pumping volume.
VOLUME (-) - used to decrease the pumping volume.
Figure 36. Antenna Installation
ANTENNA
KNOCK-OUT
HOLE
ANTENNA
CONNECTOR
CABLE
CONTROL BOX
CONNECTOR
REAR OF
CONTROL BOX
Figure 37. Radio Remote Control
E-STOP
ON
OFF
PUMP
REV
VOLUME VOLUME
PUMP
ON/OFF
POWER LED
NOTE: OLDER MODELS
MAYINDICATE
INSTEAD OF
FLOW
VOLUME
BATTERY LED