Marmitek MS9470 Home Security System User Manual


 
2 MARMITEK
INTRODUCTION
Congratulations! You purchased a Marmitek Security System. Marmitek
Security Systems are quality products and are manufactured with high
precision.
The Marmitek Security System protects yourself and your home against
intruders. On top of that your Marmitek Security System can control lights
and appliances throughout your house (using the existing mains wires!). In
that way your Marmitek Security System can create a “lived-in look” when
you are away. Optional plug-in modules, wall switches or DIN-Rail modules
(at the distribution panel) allow switching of appliances or dimming of lights.
These modules can be programmed to be part of the alarm signalling.
Up to 16 wireless (radio) sensors can be installed onto the supplied Security
Console SC2800. This base station can be operated by up to 8 wireless
(radio) remote controllers. On top of that you can operate your Marmitek
Security System via the keyboard of the Security Console SC2800.
When an alarm situation occurs, the built-in telephone voice dialler of the
Security Console SC2800 will dial up to 4 pre-programmed telephone
numbers and play your pre-recorded alarm message. Anyone picking up the
phone on the other end responds to the alarm message by pressing a single
digit on that telephone. This will stop further dialling and allows the person
who picked up the phone to “listen-in“ to the protected premises by means
of the built-in microphone of the Security Console SC2800. Failing sensors
will be reported in a similar way by playing a fixed service message.
It is important that you carefully read through all of the chapters of this
users’ guide before starting the installation. Also when a third party is
installing the system for you, you have to read this manual carefully as it
contains important information regarding operation and use of the
Marmitek SC2800.
In case of any problems during installation or use of the system, please read
first through the troubleshooting chapter in the back of this users’ guide.
You also can contact the Martmitek web site (marmitek.com) for additional
information. In case you cannot fix the problem with these
recommendations, you then have to contact the dealer where you
purchased your Marmitek Security System.
CONTENTS
1. General 3
2. Safety Precautions 3
3. Marmitek Systems 4
3.1 Components 4
3.2 Important Features 4
4. Installation of the components 5
4.1 Signals and range 5
4.2 SC2800 Security Console (base station) 6
4.3 DS10 Door/Window Sensors 8
4.4 MS10 Motion Sensors 9
4.5 KR21 Key Fob Remote Control 10
4.6 SH624 System Remote Control (optional for MS9470) 10
4.7 LM12 Lamp Module (optional for MS9470) 11
4.8 Installation of other (wired) sensors 12
4.9 Installation of the GB10 Glass Break Sensor 12
4.10 DigiMax 210 wireless thermostat (OPTION) 14
5. Programming the SC2800 base station 15
5.1 Registration of radio sensors 15
5.2 Registration of wireless remote controls 16
5.3 Set siren on/off (silent alarm) 16
5.4 Programming of telephone numbers 17
5.5 Recording the alarm message 18
5.6 Delayed alarm times 19
5.7 Jamming detection on/off 20
5.8 Change personal identification code (PIN) 21
5.9 Erasing a radio sensor 22
5.10 Erasing of all settings 22
6. Operating the system 23
6.1 Install, Run 1 and Run 2 23
6.2 Arming the system 23
6.3 When an alarm situation occurs 24
6.4 Disarming the system 25
6.5 Disarming after an alarm (reset) 25
6.6 Panic alarm 26
6.7 Zone indicators 26
6.8 Controlling lights and appliances (Home Automation) 27
6.9 Lifestyle programming 29
7. SC2800 dial-in features 30
8. Setting ‘sensor error’ message 31
9. Troubleshooting 32