Filter
Top Products
44008-01 • 02/10/10 • Hunter Fan Company
9
9
3
.
Operation (Cont.)
Auto season changeover allows you the option of setting your thermostat to switch between heating and cooling modes
automatically. e thermostats system mode must be in auto for the auto season changeover feature to work. We recommend
keeping your programmed heating and cooling temperatures at least 4°F (3°C) apart to allow the auto season changeover to
occur. However, if your heating and cooling programs set temperatures are close, there is a built-in program to prevent the
thermostat from changing unnecessarily.
Auto Season Changeover is disabled when the thermostat is in Temporary or Permanent Override, or Vacation Hold, as these
overrides are energy saving settings. While in any of these modes, “auto” will be temporarily removed form the LCD display.
“auto” will return when these holds are cleared. Auto Season Changeover will still function in Home Today mode, as this is a
comfort setting.
Example: If your Heat is set to 68°F and your cooling is set to 78°F, auto season changeover would work as follows. If the room
temperature rises above 78°F, then the thermostat will automatically change to cool mode and turn on the air conditioner.
Likewise, the thermostat will automatically change to heat mode and turn on heat when the room temperature falls below
68°F.
Auto Season Changeover
is Hunter patented feature allows you to temporarily override your program settings on days when you are normally away
from home with one key press.
Press “
home today” to enter the home today override. e highest program temperature for today will be selected from your
programs in Heat mode and become the set temperature. (In Cool mode, the lowest program temperature will be the set
temperature.) “Home” will alternate on the display with the day and any other messages.
When activated during program 1 or 2, home today will automatically return to program control at the start of program 4 that
day. If home today is pressed after the start of program 3, the thermostat will remain in home today mode until program 1 the
next day. If home today is already active, you may extend it to program 1 of the next day by pressing the “
home today” again
after the start time of the third program. If the system is changed between Heat and Cool modes (either manually or by Auto
Season Changeover) during the “Home Today” override period, the set point temperature will be automatically updated. It will
automatically change from the highest heat program set point to the lowest cool program set point, or from the lowest cool
program set point to the highest heat program set point.
Press
ret/clear
to exit home today mode before the schedule ending time. Home will be removed from the screen, and the
thermostat will return to the current program.
To change the temperature manually:
Press and hold the or buttons for 1 second or until the screen blinks. en use the arrow buttons to adjust the
temperature. Manually changing the set temperature will not aect the Home Today ending time. However, the set temperature
will not change automatically with a manual or Automatic change between heating and cooling. You may also press the “
home today” key while in temporary manual override. e operation is the same as the point above.
Home Today
4
.
Features
e thermostat provides a 3.5 minute delay after shutting o the heating or cooling system before it can be restarted. is
feature will prevent damage to your system caused by rapid cycling.
System Protection
Two fresh AA alkaline batteries should provide one year of service (depending on backlight usage). However, when the batteries
become drained, the Low Battery Indicator will ash on the display. when this message occurs, install new alkaline batteries.
You have appoximately one minute to change the batteries and keep the thermostat’s clock and program settings. Once the
batteries have become too low to ensure proper operation, your system will be turned o. e display will be clear except for
the ashing Low Battery Indicator on the LCD display, and all programming will be lost.
To check the life of the battery:
Press
option
twice. Press the
ret/clear
button or wait 15 seconds to return to the main display.
CAUTION: When only the battery Icon ashes on the display, the thermostat has shut down and your system will no longer
operate. In this condition, there is no temperature control for your dwelling.
NOTE: If you plan to be away from the premises for over 30 days, we recommend that you replace the old batteries with new
alkaline batteries prior to leaving.
Low Battery Indicator