Filter
Top Products
27
P61A Pellet Stove
1. Air-fuel ratio is too rich.
A. Feed rate too high.
B. Draft too low caused by a gasket leak.
1. Feed rate too low
2. Draft too low because of gasket leak.
3. Poor quality or damp pellets
4. Combination of 1 and 2.
Whenever your stove is not burning, take the op-
portunity to scrape the burn pot to remove carbon
buildup. A vacuum cleaner is handy to remove the
residue.
Carbon buildup can be scraped loose with the re
burning using the special tool provided with your stove.
Scrape the oor and sides of the burn pot. The carbon
will be pushed out by the incoming fuel. Always wear
gloves to do this.
Turn the Temp Dial to number 1 approximately 30
minutes before removing ashes. This will result in a
cooler stove and ash pan.
You may notice some smoke and odor during the
rst ring of the appliance. This is likely part of the paint
curing process, and will diminish with time. Consider
keeping a window open during the rst hour of opera-
tion, to remove any associated odors.
1. No fuel in hopper.
2. Firebox draft may be too low for sensing switch in
feeder circuit to operate. ,
loose or missing gasket on doors or hopper lid.
3. Hopper lid must contact the lid position switch.
4. Feed motor will not run until the ESP control
senses a certain temperature. Maybe you did not
put enough fuel or starting gel in the burn pot before
manually lighting the re.
5. Restriction in the hopper or feeder. Remove all
fuel and examine. Clear the obstruction.
6. Feed motor has failed.
1. Feed rate too high.
2. Poor air to fuel mixture. (Check burn pot clean-
out cover and air intake).
3. Burn pot or heat exchanger tubes may need to
be cleaned.
4. Combination of all the above.
5. : A 6 blink control board status
indication is caused by poor or incomplete combus-
tion. The circuit board has the ability to track the
combustion through feed settings and ESP tem-
peratures. When the control board has calculated
poor or incomplete combustion, it will shut down
the unit as a safety feature. (Poor or incomplete
combustion is a contributor of creosote which may
cause a chimney re)
A 6 blink status may be caused by several
things:
1. Blocked or partially blocked ue.
2. Blocked or partially blocked inlet air.
a. Backdraft damper on the inlet pipe may be
stuck closed.
b. If outside air is installed, the inlet cover may
be blocked.
3. The air chamber under the burnpot may be lled
with nes and small bits of ash.
4. The holes in the burnpot may be getting lled
with ash or carbon buildup.
5. Combustion blower fan blades may need
cleaned.
6. Fuel restrictions as noted above.
Seal the vent pipe joints and connection to stove
with silicone. The exhaust vent is the only part of
the system that is under positive pressure.
1. No fuel in hopper.
2. Draft is too low, blocked ue.
3. Something is restricting fuel ow.
4. Hopper lid not closed properly.
5. Feed motor or combustion blower has failed.
Pellet fuels are put into 3 categories in terms of
ash content. Premium at 1% or less, Standard at 3%
or less and all others at 3% or more.
The P61A is capable of burning all 3 categories
of pellets, and up to a 50% mixture with shelled corn,
see next page for special instructions.
It should be noted, that higher ash content will
require more frequent ash removal, scraping of the
burn pot, and may provide less BTU's per pound.
The moisture content of pellets must not exceed
8%, corn 15%. Higher moisture will rob BTU's and may
not burn properly.
Fuel should be stored in a dry area, outside of the
stove's installation clearance area and outside of the
space required for charging and ash removal. See
Page 7.