First Alert FA168CPS Home Security System User Manual


 
34
ZONE TYPE DEFINITIONS
Zone types define the way in which the system responds to faults in each zone.
Type 00 Zone Not Used
Program a zone with this zone type if the zone is not used.
Type 01 Entry/Exit Burglary #1
Assign to zones that are used for primary entry and exit.
Provides entry delay when zone is faulted if control is armed in
the Away, Stay, or Night-Stay modes.
No entry delay provided when the panel is armed in the
Instant/Maximum mode.
Entry delay #1 is programmable for each partition (field *35).
Exit delay begins whenever the control is armed, regardless of
the arming mode selected, and is programmable (field
34).
Type 02 Entry/Exit Burglary #2
Assign to zones that are used for entry and exit and require
more time than the primary entry/exit point.
Provides a secondary entry delay, similar to entry delay #1.
Entry delay #2 is programmable for each partition (field *36).
Exit delay is same as described for Type 01.
Type 03 Perimeter Burglary
Assign to all sensors or contacts on exterior doors and windows.
Provides an instant alarm if the zone is faulted when the panel is
armed in the Away, Stay, Night-Stay, Instant or Maximum modes.
Type 04 Interior Follower
Assign to a zone covering an area such as a foyer, lobby, or
hallway through which one must pass upon entry (to and from
the keypad).
Provides a delayed alarm (using the programmed entry 1 time)
if the entry/exit zone is faulted first. Otherwise this zone type
gives an instant alarm.
Active when the panel is armed in the Away mode.
Bypassed automatically when the panel is armed in the Stay or
Instant modes; if armed in Night-Stay mode, zones assigned to
zone list 05 (night-stay zone list) are not bypassed when
system armed in Night-Stay mode.
Type 05 Trouble by Day/Alarm by Night
Assign to a zone that contains a foil-protected door or window
(such as in a store), or to a zone covering a sensitive area such
as a stock room, drug supply room, etc.
Can also be used on a sensor or contact in an area where
immediate notification of an entry is desired.
Provides an instant alarm if faulted when armed in the Away,
Stay, Night-Stay, Instant or Maximum (night) modes.
During the disarmed state (day), the system will provide a
latched trouble sounding from the keypad (and a central station
report, if desired).
Type 06 24-hr Silent Alarm
Usually assigned to a zone containing an emergency button.
Sends a report to the central station but provides no keypad
display or sounding.
Type 07 24-hour Audible Alarm
Assign to a zone that has an emergency button.
Sends a report to the central station, and provides an alarm
sound at the keypad, and an audible external alarm.
Type 08 24-hour Auxiliary Alarm
Assign to a zone containing an emergency button, or to a zone
containing monitoring devices such as water or temperature
sensors.
Sends a report to the central station and provides an alarm
sound at the keypad. (No bell output.)
Type 09 Supervised Fire
Provides a fire alarm on short circuit and a trouble condition on
open circuit. A fire alarm produces a pulsing bell output.
This zone type is always active and cannot be bypassed.
Type 10 Interior w/Delay
Provides entry delay (using the programmed entry time), if
tripped when the panel is armed in the Away mode.
Entry Delay 1 begins whenever sensors in this zone are
violated, regardless of whether or not an entry/exit delay zone
was tripped first.
Bypassed when the panel is armed in the Stay or Instant
modes; if armed in Night-Stay mode, zones assigned to zone
list 05 (night-stay zone list) are not bypassed when system
armed in Night-Stay mode.
Type 12 Monitor Zone
Works as a dynamic monitor of a zone fault/trouble (not alarm). In
the case of a short/open, the message, "*ALARM*-24 Hr. Non-Burg.
-#XXX " (where XXX is the zone number) will be sent to the Central
Station. The system keypad will display a “check” message
indicating the appropriate zone (but keypad beeping does not
occur). Upon restoral of the zone, the message, "*RESTORE*-24
Hr. Non-Burg. -#XXX " will be sent to the Central Station.
The “check” message will automatically disappear from the keypad
dynamically, when the zone restores; a user code + off sequence is
not needed to reset the zone.
Faults of this zone type are independent of the system, and can
exist at the time of arming without interference.
Since this is a “trouble” zone type, do not use this zone type with
relays set to activate upon “alarm.”
Type 14 24 Hour Carbon Monoxide Monitor
Assigned to any zone with a carbon monoxide detector.
A carbon monoxide alarm produces keypad and detector sounding
(does not affect bell output).
Always active and cannot be bypassed.
Type 16 Fire w/Verification
Provides a fire alarm when zone is shorted, but only after alarm
verified.
Verifies alarm by resetting smoke detectors after short is detected
(removes power 7 seconds for zone 1, 3 seconds for trigger output).
Another short circuit within 90 seconds triggers fire alarm.
Provides a trouble response when zone is open.
Type 20 Arm-Stay (BR only)
Arms the system in Stay mode when the zone is activated.
Pushbutton units send the user number to the central station when
arming or disarming.
User number for button must be assigned.
Type 21 Arm-Away (BR only)
Arms the system in Away mode when the zone is activated.
Pushbutton units send the user number to the central station when
arming or disarming.
User number for button must be assigned.
Type 22 Disarm (BR only)
Disarms the system when the zone is activated.
User number for button must be assigned.
Type 23 * No Alarm Response
Can be used on a zone when an output relay action is desired, but
with no accompanying alarm (e.g., lobby door access).
Type 24 Silent Burglary
Usually assigned to all sensors or contacts on exterior doors and
windows where bells and/or sirens are NOT desired.
Provides an instant alarm, with NO audible indication at any keypad
or external sounder, if the zone is faulted when the system is armed
in the Away, Stay, Instant, or Maximum modes.
A report is sent to the central station.
Type 77 Keyswitch
Assign to zone wired to a keyswitch.
Do not use input type “BR” devices with this zone type.
Type 81 AAV Monitor Zone
Assign to zone connected to AAV module.
Monitors 2-way voice sessions as follows:
- When the zone is faulted, all alarm sounding and dialer reporting
stops, except for fire alarms, which immediately terminate the
voice session and cause a fire report to be sent.
- When the zone is restored (session ended), sounding resumes (if
bell timeout has not expired) and reports that were stopped are
sent.
Types 90-93 Configurable
Allows for various custom responses. Options include response to
entry/exit delays, response opens/shorts, types of alarm/trouble
sounding, dial delay, and unique Contact ID report codes. Types 92
and 93 can only be programmed via downloader. UL installations:
Zone Types 90 -93 may not be used as fire or burglar alarm zones on
fire or UL burglar alarm installations.
* The system can still be armed when these zone types are in a
faulted condition.