Filter
Top Products
– 16 –
KEYPAD OPTIONS *190-*199
To enable keypads:
1. Set desired address at keypad (refer to keypad’s instructions for setting the address).
2. Use data fields *190-*196 to enable keypad addresses, assign a partition, enable sound options in field.
3. Use fields *197, *198, and *199 to turn on partition number display, exit time interval display, and select fail display mode.
4. Set keypad-related data fields as appropriate: *21 Quick Arm Enable, *23 Forced Bypass, *84 Auto STAY Arm
NOTES: 1. Options for keypad 1, address 16, are set by the factory and cannot be changed.
2. Each keypad must be assigned a unique address. Keypads programmed with the same address will give
unpredictable results.
∗
∗∗
∗190
Keypad 2 Device Address 17
Partition/ Enable:
FA168CPS: Enter partition where:
0 = keypad disabled
1-3 = part. no. (3 = common)
FA148CP:
0 = disable
1 = enable
Sound: 0 = no suppression
1 = suppress arm/disarm and Entry/Exit
beeps
2 = Suppress chime beeps only
3 = suppress arm/disarm, Entry/Exit,
and chime beeps
[0] [0]
Partition/ Sound
Enable
Partion/Enable: For FA168CPS, enter the partition in which the
keypad is located; for FA148CP, enter 1 to enable, or 0 to disable the
keypad.
Sound: Enter the desired sound option for this keypad.
∗
∗∗
∗191
Keypad 3 Device Address 18
See field ∗190 for entries.
[0] [0]
Part/Enable Sound
∗
∗∗
∗192
Keypad 4 Device Address 19
See field ∗190 for entries.
[0] [0]
Part/Enable Sound
∗
∗∗
∗193
Keypad 5 Device Address 20
See field ∗190 for entries.
[0] [0]
Part/Enable Sound
∗
∗∗
∗194
Keypad 6 Device Address 21
See field ∗190 for entries.
[0] [0]
Part/Enable Sound
∗
∗∗
∗195
Keypad 7 Device Address 22
See field ∗190 for entries.
[0] [0]
Part/Enable Sound
∗
∗∗
∗196
Keypad 8 Device Address 23
See field ∗190 for entries.
[0] [0]
Part/Enable Sound
∗
∗∗
∗197
Exit Time Display Interval
0 = no display
1-5 = seconds between display refresh
[0]
If enabled, keypads display the exit time remaining after arming the
system, updated at the interval selected (i.e. if the exit delay is 30
seconds and “2” is selected in this field, the keypad display refreshes
every 2 seconds, displaying 30, 28, 26, 24, etc.).
An interval greater than “1” may be necessary for some older keypads
to allow users time to enter key presses between display updates.
NOTE: If enabled and using only 2-digit fixed-word keypads (e.g.,
FA245RF), do not set exit delay time greater than 96 seconds. Using a
longer delay time may cause end-user confusion because 2-digit
display keypads cannot display times greater than “99.” If longer exit
time is required by the installation, it is recommended that the Exit
Time Display option be disabled (“0”).
TOUCH SCREEN DEVICE NOTE: If using more than one touch screen
device (e.g., FA700KP, Symphony) with the system, leave field *197
Exit Time Display Interval set to the default value “0.” The FA700KP
automatically displays remaining exit time in one-second increments.
∗
∗∗
∗198
Display Partition Number
0 = no
1 = yes (partition no. displayed)
[0]
(FA168CPS; for Alpha Display Keypads)
If selected, the partition number is displayed in the upper-left corner of
the display. This is useful when using the GOTO partition function.
∗
∗∗
∗199
ECP Fail Display
0 = 3-digit display
“1” + device address)
1 = 2-digit fixed-display as “91
[0]
Select “0” if using Alpha keypads and/or 3-digit Fixed-Word Displa
y
keypads. ECP faults will display “1” plus the device address (00-30) of
device causing the fault (e.g., faults on device 07 display as “107”).
Select “1” if using 2-digit Fixed-Word Display keypads (e.g., certain
6128 series keypads). If selected, ECP faults for all devices will display
as “91” on 2-digit displays, and “191” on 3-digit or Alpha keypads.