Filter
Top Products
2
(FIELD PROVIDED AND INSTALLED)
Fig. 2 — 38HDF,HDR Unit Dimensions
NOTE: Dimensions shown in feet-inches. Dimensions in ( ) are millimeters.
UNIT MODELS
CHASSIS
SIZE
(Reference)
ABCDEFG H JKL NP
38HDF
Unit Size
38HDR
Unit Size
018 018 0
2′-1
1
/
8
″ 3′-0
15
/
16
″ 1′-2
9
/
16
″ 1′-4″ 1′-11
7
/
16
″ 1′-5
3
/
16
″ 1′-5
1
/
8
″ 1′-10″ 1′-1″ 0′-6
5
/
8
″ 0′-11
1
/
4
″ 0′-2
15
/
16
″ 0′-6″
(638.2) (938.2) (369.9) (406.4) (595.3) (436.6) (435) (559.1) (330.2) (168.3) (285.8) (75) (152.4)
024,030 024 0.6
2′-7
1
/
8
″ 3′-0
15
/
16
″ 1′-2
9
/
16
″ 1′-4″ 1′-11
7
/
16
″ 1′-5
3
/
16
″ 1′-11
1
/
8
″ 2′-4″ 1′-2″ 0′-6
3
/
4
″ 0′-11
5
/
8
″ 0′-2
15
/
16
″ 0′-6″
(790.6) (938.2) (369.9) (406.4) (595.3) (436.6) (587.4) (711.5) (355.6) (171.5) (295.3) (75) (152.4)
036 030,036 1.0
3′-1
3
/
16
″ 3′-8
9
/
16
″ 1′-5
1
/
16
″ 1′-6
7
/
16
″ 2′-6
1
/
2
″ 1′-7
5
/
8
″ 2′-5
3
/
16
″ 2′-10
1
/
16
″ 1′-1
11
/
16
″ 0′-8
1
/
8
″ 1′-3
7
/
8
″ 0′-3
7
/
16
″ 0′-6
1
/
2
″
(944.6) (1131.9) (433.4) (468.3) (774.7) (498.5) (741) (865.5) (347.7) (206.4) (403.2) (88) (165.4)
— 048,060 1.6
3′-7
3
/
16
″ 3′-8
9
/
16
″ 1′-5
1
/
16
″ 1′-6
7
/
16
″ 2′-6
1
/
2
″ 1′-7
5
/
8
″ 2′-1
13
/
16
″ 3′-4
1
/
16
″ 1′-2
1
/
2
″ 0′-8
1
/
2
″ 1′-6
7
/
8
″ 0′-3
7
/
16
″ 0′-6
1
/
2
″
(1097) (1131.9) (433.4) (468.3) (774.7) (498.5) (893.4) (1017.9) (354.2) (215.9) (479.4) (88) (165.4)
UNIT SIZE
M OPERATING WT
in. mm lb kg
38HDF
018
5
/
8
15.88 166 75.3
024
5
/
8
15.88 176 79.8
030
3
/
4
19.05 187 84.8
036
3
/
4
19.05 250 113.4
38HDR
018
5
/
8
15.88 166 75.8
024
5
/
8
15.88 176 79.8
030
3
/
4
19.05 187 84.8
036
3
/
4
19.05 250 113.4
048
7
/
8
22.22 278 126.1
060
7
/
8
22.22 306 138.8
NOTES:
1. Required clearances: with coil facing wall, allow 6 in. minimum clearance
on coil side and coil end, and 3 feet minimum clearance on compressor
end and fan side. With fan facing wall, allow 8 in. minimum clearance on
fan side and coil end, and 3 feet minimum clearance on compressor end
and coil side. With multi-unit application, arrange units so discharge ofone
does not enter inlet ofanother.
2. Dimensions in parenthesis are in millimeters.
3. Center of Gravity .
UNIT SIZE
MINIMUM MOUNTING PAD
DIMENSIONS
Support Feet
ft-in. mm
CHASSIS SIZES 0 & .6 1′-11″x3′-6″ 584.2 x 1066.8
CHASSIS SIZES 1 & 1.6 2′-0″ x4′-2″ 609.6x 1270