Filter
Top Products
Trolley Arm Hookup
Tools: Needle nose pliers
NOTE: If Wayne-Dalton operator/ trolley bracket was installed, follow these directions.
Trolley arm
Operator
bracket tabs
5/16”-18 Nut
3/8” Washer
5/16”-18 x 3-1/2”
Hex bolt
Side Lock
Tools: Power drill, 7/16” Socket driver, Tape measure
Install the side lock on the second section of the door. Square the lock assembly with the door
section, and align with the square hole in the vertical track. The side lock should be spaced ap-
self drilling screws.
IMPORTANT: SIDE LOCKS MUST BE REMOVED OR MADE INOPERATIVE IN THE UNLOCKED
POSITION IF AN OPERATOR IS INSTALLED ON THE DOOR.
(4) 1/4”-20 x 11/16”
Self drilling screws
Square hole in
vertical track
Second section
Side lock
End stile
1/8”
Pull Rope
Tools: Power drill, 1/8” Drill bit, Tape measure
WARNING WARNING
DO NOT INSTALL PULL ROPES ON DOORS WITH ELECTRIC OPERATORS. CHIL-
DREN MAY BECOME ENTANGLED IN THE ROPE CAUSING SEVERE OR FATAL
INJURY.
screw eye and to the bottom bracket as shown.
Bottom bracket
Pull rope
No. 6 Screw eye
Pull rope
48” to 50”
From floor
Cleaning Your Garage Door
IMPORTANT: DO NOT USE A PRESSURE WASHER ON YOUR GARAGE DOOR!
While factory-applied finishes on garage doors are durable, it is desirable to clean them on a
routine basis. Some discoloration of the finish may occur when a door has been exposed to
dirt-laden atmosphere for a period of time. Slight chalking may also occur as a result of direct
exposure to sunlight.
Cleaning the door will generally restore the appearance of the finish. To maintain an aesthetically
pleasing finish of the garage door, a periodic washing of the garage door is recommended.
THE FOLLOWING CLEANING SOLUTION IS RECOMMENDED:
A mild detergent solution consisting of one cup detergent (with less than 0.5% phosphate) dis-
solved into five gallons of warm water will aid in the removal of most dirt.
NOTE: The use of detergents containing greater than 0.5% phosphate is not recommended for
use in general cleaning of garage doors.
NOTE: Be sure to clean behind weather stripping on both sides and top of door.
CAUTION: NEVER MIX CLEANSERS OR DETERGENTS WITH BLEACH.
GLASS CLEANING INSTRUCTIONS
Clean with a mild detergent solution (same as above) and a soft cloth. After cleaning, rinse
thoroughly.
ACRYLIC CLEANING INSTRUCTIONS
Clean acrylic glazing with nonabrasive soap or detergent and plenty of water. Use your bare
hands to feel and dislodge any caked on particles. A soft, grit-free cloth, sponge or chamois may
be used to wipe the surface. Do not use hard or rough cloths that will scratch the acrylic glazing.
Dry glazing with a clean damp chamois.
NOTE: Do not use any window cleaning fluids, scouring compounds, gritty cloths or solvent-
based cleaners of any kind.
Painting Your Garage Door
SURFACE PREPARATION FOR PAINTING
Wax on the surface must be removed or paint peeling/ flaking will result. To remove this wax,
it will be necessary to lightly scuff the surface with a fine steel wool pad saturated with soapy
water. A final wipe and rinse should be done with clean water only to remove any loose particles
and any soapy film residue.
Surface scratches, which have not exposed the metal substrate, can be lightly buffed or sanded
with 0000 steel wool or no. 400 sand paper to create a smoother surface. Care must be taken
to not expose the substrate under the paint. Once the substrate is exposed, the likelihood for
rusting is greatly increased.
If substrate is exposed, it must be treated to prevent rust from forming. Sand the exposed area
lightly and paint with a high quality metal primer specifically intended for galvanized surfaces
to protect the area from corrosion. Allow for drying time on primer can label before applying
topcoat.
The surface of the factory-applied finish, that is being painted, must not be too smooth, or the
paint will not adhere to it. It is advisable to test in an inconspicuous area, to evaluate adhesion.
If poor adhesion is observed, surface preparation for painting the factory-applied finish must
be repeated until desired results are achieved. Again, care must be taken to not expose the
substrate under the paint.
PAINTING
After surface has been properly prepared, it must be allowed to dry thoroughly, and then coated
immediately with premium quality latex house paint. Follow paint label directions explicitly. Oil
base or solvent base paints are not recommended. Please note that if substrate is exposed and
not properly primed, painting with latex paint may cause accelerated rusting of the metal in the
exposed area.
NOTES:
1. Re-painting of finish painted steel doors cannot be warranted, as this condition is totally
beyond the door manufacturer’s control.
2. Consult a professional coatings contractor if in doubt about any of the above directions.
3. Follow directions explicitly on the paint container labels for proper applications of coatings and
disposal of containers. Pay particular attention to acceptable weather and temperature condi-
tions in which to paint.
Operation and Maintenance
OPERATING YOUR GARAGE DOOR…
Before you begin, read all warning labels affixed to the door and the installation instructions and
owner’s manual. When correctly installed, your Wayne-Dalton door will operate smoothly. Always
operate your door with controlled movements. Do not slam your door or throw your door into the
open position, this may cause damage to the door or its components. If your door has an electric
opener, refer to the owner’s manual to disconnect the opener before performing manual door
operation below.
Manual door operation:
For additional information on manual garage door operations go to www.dasma.com and
reference TDS 165.
IMPORTANT: DO NOT PLACE FINGERS OR HANDS INTO SECTION JOINTS WHEN OPENING
AND/OR CLOSING A DOOR. ALWAYS USE LIFT HANDLES/ SUITABLE GRIPPING POINTS WHEN
OPERATING THE DOOR MANUALLY.
13
Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer,
refer to your local yellow pages business listings or go to the Find a Dealer section online at www.wayne-dalton.com
Optional Installation