Filter
Top Products
PG. 14
DIM Y
HEADER TO
SHAFT
CENTERLINE
MINIMUM
HEADROOM
REQUIRED
(REFER TO
HEADROOM
CHART)
8 for 2 TRACK
12 for 3 TRACK
EXTEND JAMBS TO OPENING HEIGHT plus
DIM Y plus 1 1/2 (MINIMUM LENGTH)
TORSION SHAFTS REQUIRE 10 OF
SIDEROOM FOR SOLID SHAFTS and
5 OF SIDEROOM FOR TUBULAR
SHAFTS
NOTE: HEADROOM CAN BE REDUCED 2-1/2 BY
USING THE QUICK CLOSING TOP FIXTURE OR
BY SHORTENING THE VERTICAL TRACKS BY
3 MAX.
SIDEROOM REQUIREMENTS
2 inch TRACK
3 inch TRACK
PRECAST WALL WITH
CORNER ANGLE
3 TRACK
PRECAST WALL WITHOUT
CORNER ANGLE
3 TRACK
STEEL JAMBS
3 TRACK
WOOD JAMBS
3 TRACK
STEEL JAMBS
2 TRACK
PRECAST WALL WITH
CORNER ANGLE
2 TRACK
PRECAST WALL WITHOUT
CORNER ANGLE
2 TRACK
WOOD JAMBS
2 TRACK
1 OVERLAP
1
1/2- 5/8
4
1 OVERLAP
1
1/2- 5/8
4
1
1/2- 5/8
4
FLUSH
1
4
4 3/4
5/16 X 1
DRILLING /
TAPPING
SCREW
3/8 X 3 MIN.
SLEEVE
ANCHOR
OPTIONAL
MOUNTING
BRACKET
5
OPTIONAL
MOUNTING
BRACKET
3/8 X 3 MIN.
SLEEVE
ANCHOR
5/16 X 1
DRILLING /
TAPPING
SCREW
2 X 6 JAMB IS
RECOMENDED
1/2- 5/8
2 1/2 MIN.
SIDE ROOM
1 OVERLAP
1 1/2
1/2- 5/8
3 1/2
1 OVERLAP
1 1/2
1/2- 5/8
3 1/2
1 OVERLAP
1 1/2
1/2- 5/8
3 1/2
FLUSH
1 1/2
3 1/2
4 3/4
5/16 X 1
DRILLING /
TAPPING
SCREW
3/8 X 3 MIN.
SLEEVE
ANCHOR
OPTIONAL
MOUNTING
BRACKET
4 3/4
OPTIONAL
MOUNTING
BRACKET
3/8 X 3 MIN.
SLEEVE
ANCHOR
5/16 X 1
DRILLING /
TAPPING
SCREW
2 X 6 JAMB IS
RECOMENDED
1/2- 5/8
2 1/2 MIN.
SIDE ROOM
2 1/2 MIN.
SIDE ROOM
3 1/2 MIN.
SIDE ROOM
5 MIN.
SIDE ROOM
3 MIN.
SIDE ROOM
3 MIN.
SIDE ROOM
3 MIN.
SIDE ROOM
5/16 X 1 5/8
LAG SCREW
5/16 X 1 5/8
LAG SCREW
1 OVERLAP
(3) 1/4-20 X 7/8 SELF
DRILLING TEK SCREWS
(4) 1/4-20 X 5/8 SELF
DRILLING TEK SCREWS
OPERATOR BRACKET
U-BAR
Fig. AA
U-BAR
OPERATOR BRACKET
(4) 1/4-20 X 5/8 SELF
DRILLING TEK SCREWS
(6) 1/4-20 X 7/8 SELF
DRILLING TEK SCREWS
Fig. BB
6 GIRT
OPERATOR
BRACKET
(12) 1/4-20 X 7/8 SELF
DRILLING TEK SCREWS
Fig. CC
(4) 1/4-20 X 7/8 SELF
DRILLING TEK SCREWS
THROUGH OPERATOR
BRACKET INTO GIRT
MODELS 5155 & 5255
PART NUMBER 293009 38in WIDE X 19 5/8 in HIGH FOR 24 in TOP SECTION
PART NUMBER 293010 38in WIDE X 16 7/16 in HIGH FOR 21 in TOP SECTION
ATTACH USING (12) PRE DRILLED HOLES
MODELS 5150 & 5200
PART NUMBER 295687 50 in WIDE X 17 1/4 in HIGH FOR 24 in TOP SECTION
PART NUMBER 295686 50 in WIDE X 14 in HIGH FOR 21 in TOP SECTION
MOUNT BRACKET OVER HINGES IN CENTER OF SECTION, DRILL (2) 9/32
HOLES IN EACH CORNER AND SECURE USING (12) 14-20 X 7/8 SELF
DRILLING TEK SCREWS (SEE NOTE BELOW)
THIS RECTANGULAR DESIGN IS FOR DOORS OVER 20 ft. 2 in. WIDE.
NOTE: MODEL 5150 & 5200 DOORS BETWEEN 20 ft 2 in AND 24 ft 2 in
REQUIRE THAT THE OPERATOR BE MOUNTED OFF CENTER SO THE
OPERATOR BRACKET MOUNTS TO THE HINGE POINTS.
STEP 13: Operator Trolley Bracket Installation: Attach the operator trolley bracket as illustrated in Fig. AA. This trolley
bracket is limited to doors 142 X 10 (5 Sections high and smaller).
For doors 142 X over 10 (5 sections) and 143 thru 202 by all heights see Fig. BB.
For doors over 202 by all heights see Fig. CC.
MODELS 5150, 5155, 5200, & 5255
PART NUMBER 295689
THIS DESIGN IS FOR DOORS UP TO
14 2 WIDE AND OVER
10 (5 SECTIONS HIGH) AND
143 THRU 202 BY ALL HEIGHTS
NOTE: TROLLEY BRACKET TO BE
INSTALLED OFFSET FOR ODD
PANELS
MODELS 5150, 5155, 5200, &5255
PART NUMBER 107319
DOORS UP TO 14 ft 2 in WIDE X 10
(5 SECTIONS HIGH)
NOTE: TROLLEY BRACKET TO BE
INSTALLED OFFSET FOR ODD PANELS
PG. 3