Sony RCP 920 Garage Door Opener User Manual


 
Initial Settings
71
3
Turn the right adjustment knob to move the cursor to
the item you want to change.
4
Change the sensitivity for each adjustment knob.
1 Press ENTER button to enable configuration.
The cursor appears as “?” and the setting flashes.
2 Turn the right adjustment knob to change the
setting, and press ENTER button.
The sensitivity is changed.
5
Press CLEAR button.
The first screen of the RCP configuration menu
reappears.
To configure system connection settings
The RCP-920/921 supports system connections via the
CCU/CNU REMOTE connector and connections to
camera network systems via the Ethernet connector.
Perform the following steps to configure system
connection settings.
Notes
To apply the configurations, you must restart the unit.
This setting can only be configured in Engineer mode.
1
Move the cursor to SETTING in the RCP
configuration menu, and press ENTER button.
The settings and adjustment screens appear.
2
Use the v and V buttons to move through the settings
and adjustment screens, and display the <CNS
SETTING> page.
Note
The LCD can only display up to four setting items at
one time. If a page has more than four items, turn the
right adjustment knob to scroll the page.
3
Select a system connection mode.
The following three modes are available. Select one
based on your system environment.
LEGACY: Select this mode when using the CCU/
CNU REMOTE connector and a CCA-5 cable for
system connection.
BRIDGE: Select this mode when using Ethernet to
connect the RCP to a CCU or camera on a one-to-
one basis.
MCS: Select this mode when using Ethernet to
connect to a multi-camera system (MCS)
comprised of multiple cameras, CCUs, and panels.
(Factory setting: LEGACY)
Notes
For details on selecting your mode, see one of the
sections that follow: “To configure Legacy mode,”
“To configure Bridge mode,” or “To configure
multi-camera system (MCS) mode.”
When using an Ethernet connection, be sure to
configure the Ethernet connection settings.
4
Save the system connection settings.
1 Turn the right adjustment knob to move the cursor
to SET in the upper right of the screen.
2 Press ENTER button to enable configuration.
The cursor appears as “?.”
3 Press ENTER button again to save the settings.
5
Press CLEAR button.
The first screen of the RCP configuration menu
reappears.
To configure Legacy mode
1
Set the camera network system mode (CNS MODE)
to Legacy.
1 Turn the right adjustment knob to move the cursor
to CNS MODE.
2 Press ENTER button to enable configuration.
The cursor appears as “?” and the setting flashes.
ᴹᵓᵏǽᵏᵂᵉǽᵊᵌᵁᵂǽᵐᵂᵑᴻ
ᵔᵅᵆᵑᵂᴷǽǽᴮ¯ᴱ
ǽᴿᵉᴾᵀᵈᴷǽǽᴮ¯ᴯ
ǽᵁᵂᵑᴾᵆᵉᴷǽᴮ¯ᴯ
ᴹᵓᵏǽᵏᵂᵉǽᵊᵌᵁᵂǽᵐᵂᵑᴻ
ᴻᵔᵅᵆᵑᵂᴷǽǽᴮ¯ᴱ
ǽᴿᵉᴾᵀᵈᴷǽǽᴮ¯ᴯ
ǽᵁᵂᵑᴾᵆᵉᴷǽᴮ¯ᴯ
ᴹᵀᵋᵐǽᵐᵂᵑᵑᵆᵋᵄᴻǽǽǽǽǽᵐᵂᵑ
ᴻǽᵀᵋᵐǽᵊᵌᵁᵂᴷᵉᵂᵄᴾᵀᵖ
ǽǽᵊᴾᵐᵑᵂᵏǽᵆᵍǽᴾᵁᵁᵏ
ǽǽǽǽǽǽǽǽᴭᴫǽǽᴭᴫǽǽᴭᴫǽǽᴭ
ǽǽᵑᴾᵏᵄᵂᵑǽᵆᵍǽᴾᵁᵁᵏ
ǽǽǽǽǽǽǽǽᴭᴫǽǽᴭᴫǽǽᴭᴫǽǽᴭ
ᴹᵀᵋᵐǽᵐᵂᵑᵑᵆᵋᵄᴻǽǽǽǽᴻᵐᵂᵑ
ǽǽᵀᵋᵐǽᵊᵌᵁᵂᴷᵉᵂᵄᴾᵀᵖ
ǽǽᵊᴾᵐᵑᵂᵏǽᵆᵍǽᴾᵁᵁᵏ
ǽǽǽǽǽǽǽǽᴭᴫǽǽᴭᴫǽǽᴭᴫǽǽᴭ
ǽǽᵑᴾᵏᵄᵂᵑǽᵆᵍǽᴾᵁᵁᵏ
ǽǽǽǽǽǽǽǽᴭᴫǽǽᴭᴫǽǽᴭᴫǽǽᴭ