Sony RCP 920 Garage Door Opener User Manual


 
Initial Settings
69
The buzzer volume is set.
5
Press CLEAR button.
The first screen of the RCP configuration menu
reappears.
To change the security mode
The RCP-920/921 has an Engineer mode to limit access to
certain settings. These settings cannot be configured
unless Engineer mode is enabled.
1
Move the cursor to SETTING in the RCP
configuration menu, and press ENTER button.
The settings and adjustment screens appear.
2
Use the v and V buttons to move through the settings
and adjustment screens, and display the <SECURITY
MODE> page.
3
Turn the right adjustment knob to move the cursor to
MODE.
4
Change the security mode setting.
1 Press ENTER button to enable configuration.
The cursor appears as “?” and the setting flashes.
2 Turn the right adjustment knob to change the
setting to ENGINEER, and press ENTER button.
The security mode setting is changed.
5
Save the security mode setting.
1 Turn the right adjustment knob to move the cursor
to SET.
2 Press ENTER button to enable configuration.
The cursor appears as “?” and the setting flashes.
3 Press ENTER button again to save the settings.
6
Press CLEAR button.
The first screen of the RCP configuration menu
reappears.
Note
The security mode returns to NORMAL when the unit is
turned off.
To change switch assignments
You can change the functions of certain switches on the
RCP-920/921 (the camera/CCU function ON/OFF
buttons), and assign them different functions.
Note
This setting can only be configured in Engineer mode.
1
Move the cursor to SETTING in the RCP
configuration menu, and press ENTER button.
The settings and adjustment screens appear.
2
Use the v and V buttons to move through the settings
and adjustment screens, and display the <SW
ASSIGN> page.
Note
The LCD can only display up to four setting items at
one time. If a page has more than four items, turn the
right adjustment knob to scroll the page.
3
Turn the right adjustment knob to move the cursor to
the switch you want to configure.
Note
When you enter the settings configuration mode, the
LEDs for all of the assignable switches dim temporarily,
and only the switch selected for configuration with the
cursor will remain lit. This allows you to confirm the
switch for which you are currently changing the function.
ᴹᴿᵒᵗᵗᵂᵏǽᵓᵌᵉᵒᵊᵂᴻ
ᴻᵐᵔᵆᵑᵀᵅǽǽǽǽǽǽǽǽǽǽǽᴰᴭ
ǽᵀᴾᵉᵉǽǽǽǽǽǽǽǽǽǽǽǽǽᴲᴭ
ᴹᵐᵂᵀᵒᵏᵆᵑᵖǽᵊᵌᵁᵂᴻ
ᴻᵊᵌᵁᵂᴷᵋᵌᵏᵊᴾᵉ
ǽǽᵐᵂᵑᴷ
ᴹᵐᵂᵀᵒᵏᵆᵑᵖǽᵊᵌᵁᵂᴻ
ᵊᵌᵁᵂᴷᵂᵋᵄᵆᵋᵂᵂᵏ
ǽǽᵐᵂᵑᴷ
ᴹᵐᵂᵀᵒᵏᵆᵑᵖǽᵊᵌᵁᵂᴻ
ᴻᵊᵌᵁᵂᴷᵂᵋᵄᵆᵋᵂᵂᵏ
ǽǽᵐᵂᵑᴷ
ᴹᵐᵂᵀᵒᵏᵆᵑᵖǽᵊᵌᵁᵂᴻ
ǽᵊᵌᵁᵂᴷᵂᵋᵄᵆᵋᵂᵂᵏ
ᴼǽᵐᵂᵑ
ᴹᵐᵂᵀᵒᵏᵆᵑᵖǽᵊᵌᵁᵂᴻ
ǽᵊᵌᵁᵂᴷᵂᵋᵄᵆᵋᵂᵂᵏ
ᴻǽᵐᵂᵑᴷ
ᴹᵐᵔǽᴾᵐᵐᵆᵄᵋᴻ
ǽᵐᵔᴭᴮᴷᴲᴳᴭᴭᵈ
ᴻᵐᵔᴭᴯᴷᴾᵑǽᵈᵋᵂᵂ
ǽᵐᵔᴭᴰᴷᵐᵈᵆᵋǽᵁᵑᵉ