Filter
Top Products
3200 & 4200 Series -- 39 –
KEY PART NO. QTY. DESCRIPTION
1 17-0001 2 Clutch Shifter Yoke
2 33-0012 1 1-1/4 Dia Retaining
Ring
3 10-0006 2 Clutch Sprkt 50C16
1-1/4 Bore
4 15-0001 1 Jaw Clutch 1-1/4
Splined Bore
5 33-1000 1 1-1/8” Retaining Ring
6 14-0032 4 1-1/4 Pillow Block Brg
14-0002-3G 4 1-1/4 Bearing Only
(greaseable)
7 10-0068 1 Idler Sprkt 50C17
w/Bearing
10-0068-1 1 ½” Idler Bearing Only
8 25-0165 1 Idler Sprkt Mounting
Brkt
12 19-0015-1-2SP 1 Upper Gearbox Input
Shft, Drilled
13 11-0088 1 #50-69 Roller Chain
(Prior to serial
#09T2201)
11-0009 1 #50-72 Roller Chain
(Serial #09T2201 &
Later)
14 10-0064 1 Sprkt 50B19 1”B (Prior
to serial #09T2201)
10-0042 1 Sprkt 50B24 1"B (Serial
#09T2201 & Later)
15 25-0197 1 Door Catch Assembly
16 10-0070 1 Sprkt 50B32 1-1/4”
Bore, Drilled (Prior to
serial #09T2201)
10-0072 1 Sprkt 50C28 1-1/4"
Bore, Drilled (Serial
#09T2201 & Later)
17 14-0026 1 1-1/8” B Needle Bear
-
ing Only
18 10-0061 1 Idler Sprkt 50C17
w/Needle Brg
19 11-0100 1 #50-195 Roller Chain
20 23-0044 1 Idler Shaft
21 25-0164 1 Idler Bracket Weldment
23 25-0161-1 2 Chain Tensioner
Bracket
24 29-0002 4 Tensioner Spring
25 41-0001 2 Tightener, 5” Nylon
Slide
26 10-0060 1 Sprkt 50B42 1” Bore
27 11-0089 1 #50-82 Roller Chain
28 25-0198 1 Shield Mount Plate
29 24-0112-4 1 Shield Support with
Hinge
30 44-0048 1 2-Spd Frt Idler Shaft
Asm.
31 33-0044 1 Manual Holder w/Cap
KEY PART NO. QTY. DESCRIPTION
32 33-0018 2 1-1/4” Snap Ring
33 851-3118-3.5Z 2 5/16x3-1/2 MB GR5
34 43-0013 4 Spacer Plate
36 21-0001 1 Collar, Clutch
Shifter-Brass
37* 25-0189 1 2-Spd Idler Brkt Plate &
Shaft Wldmt
38* 25-0183-RHH 1 Tightener Bracket Wldmt
(High)
39* 25-0183-RHL 1 Tightener Bracket Wldmt
(Low)
40 24-0112-1 1 Plastic Door Only
41 44-0049 1 2 Spd Idler Brkt Asm
w/Sprkt
42 19-0055-4-19 1 1” ID Snap Ring
43 815-3118-Z 2 5/16” Nylon Insert Lock
Nut
44 24-0112-K 1 Shield Asm - LH Unload
24-0110-RH 1 T200 RH Cluster Shield
24-0098 1 RH Cluster Door
45 808-1.13-1.75-1
8
A/R 18 Ga. 1-1/8 ID Machine
Bushing
46* 44-0050 1 RH 2 Spd Idler Plate Asm
w/Sprkt
50 808-1.25-1.875-
10
A/R 10 Ga. 1-1/4 ID. Machine
Bushing
51 808-1.25-1.875-
14
A/R 14 Ga. 1-1/4 ID Machine
Bushing
52 808-1.25-1.875-
18
A/R 18 Ga. 1-1/4 ID Machine
Bushing
53 33-0030-RH 1 Idler Shaft Grease Bolt,
½” x 3/4”
54 30-0004 1 1/4”-28 90° Grease
Fitting
55 10-0019 1 Sprkt 50B22 1” Bore
56* 10-0004 1 Lower Shaft Sprocket,
50B17, 1-1/4” B, 1/4
Keyway
57 25-0166 1 2 Speed Bearing Support
58 14-0039 1 1” Pillow Block Bearing
59 35-0001 1 1/4 x 1/4 x 1-1/8” Key
60 35-0021 1 1/4 x 1/4 x 1-3/4” Key
* These items for RH discharge units only
TWO SPEED CLUSTER DRIVE