Filter
Top Products
3
Operation - 3 Stage Remote
(MOD 0 & A Units)
To access the controls, ip open the control panel cover
towards the bottom of the replace. (Figure 1)
A. On/Off Switch
The On/Off Switch supplies power to all replace functions
(Heater/Flame).
B. Flame Speed Control
Turn the Flame Speed Control knob to adjust the ame
speed to the desired level.
C. Interior Light Control
Turn the Interior Light Control knob to increase or decrease
the brightness of the upper lights.
D. Thermostat Control
To adjust the temperature to your individual requirements,
turn the thermostat control clockwise all the way to turn on
the heater. When the room reaches the desired temperature,
turn the thermostat knob counter clockwise until you hear
a click. Leave thermostat in this position to maintain the
room temperature at this setting. For additional heat, turn
clockwise until you hear the click again and the heater will
turn on.
E. LED Indicators
Indicates the current function of the replace: Level 1 - Flame
only; Level 2 - Flame and Low Heat; and Level 3 - Flame with
High Heat.
!
NOTE: When the rebox is changing from Low heat
to High heat the speed of the fan does not change just the
amount of heat being emitted.
F. 3-Position Switch (Figure 2)
The 3-Position Switch operates the replace levels
sequentially, ame only to ame and low heat, to ame and
high heat. The level is increased every time the “ I “ side of
the switch is pressed. The replace can be turned off at any
point by pressing the “ II ” side of the switch.
Level 1: The ame effect is turned on and the rst red
indicator light ashes momentarily.
Level 2: The ame effect remains on, the heater is activated
to the low heat setting, and the rst and second red indicator
lights ash momentarily.
Level 3: The ame effect remains on, the heater is set
to the high heat setting, and all three red indicators ash
momentarily.
!
NOTE: The heater may emit a slight, harmless odor
when rst used. This odor is a normal condition caused by
initial heating of internal heater parts and will not occur again.
A
DC FEB
Figure 2
3-Position Switch
Level 1 - Flame only
Level 2 - Flame and low heat
Level 3 - Flame and high heat
Figure 1
Resetting the Temperature Cutoff Switch
Should the heater overheat, an automatic cut out will turn the
replace off and it will not come back on without being reset.
It can be reset by switching the On/Off Switch to Off and
waiting ve (5) minutes before switching the unit back on.
If operating the unit with a remote control, the remote may
require re-initializing after turning the power off.
CAUTION: If you need to continuously reset the heater,
disconnect power and call Dimplex customer service at
1-888-DIMPLEX (1-888-346-7539).
Remote Control
The replace is supplied with a radio frequency remote
control. This remote control has a range of approximately 50
feet (15.25 m), it does not have to be pointed at the replace
and can pass through most obstacles (including walls). It is
supplied with one of hundreds of independent frequencies to
prevent interference with other units.
!
NOTE: Before attempting any operation with the remote
control, pull the plastic insulator strip out from between the
remote casing and battery cover (Figure 3).
Remote Control Initialization/Reprogramming
This procedure is required every time there is a loss of power
to the remote control in the replace. (i.e. power failure,
breaker tripped, On/Off switch is turned off)
Ensure that power is supplied through main service 1.
panel.
Locate manual controls. (Figure 1)2.
Activate On/Off switch.3.
Press and hold the 3-Position Switch in the “4. I” position
for 5-10 seconds. (The rst or second red indicator light
will ash, depending on age of model). (Figure 2)
Press the ON button located on the remote control. 5.
(Figure 3)
This will synchronize the remote control and receiver.
Remote Control Usage
The remote control operates the replace levels sequentially.
The level is increased every time the “ON” button on the
remote control is pressed. The replace can be turned off at
any point by pressing the “OFF” button on the remote control.