Filter
Top Products
INSTALLATION AND OPERATION MANUAL
MF3700, MF3800 Models
Page 17800-345-6007
CumberlandStoveWorks.com
lighter, close the door and press ON key. The sound
youhearaftertheONkeyispushedistheexhaustfan
running. After the ON key is pressed the control will read
as follows:
STARTING FIRE
LEVEL 1
ELECTRIC IGNITION INSTRUCTIONS
(MF3800 only)
After the Range has been loaded the controller will then
read as follows
ELECTRIC IGNITE
NO
YES
IMPORTANT:Beforelightingthestoveforthersttime,
make sure that no shipping items have been left inside the
reboxorashpan.
Wheninitiallyllinganemptyhopperyoumustprimethe
feed auger. To prime the auger press the ADD FUEL button.
This will turn the auger on for one minute or until the ADD
FUEL button is pressed again. Run the feed auger until
youseefuelstarttodropintotherepot.
Note: The parlor stove has been designed with a safety
switch on the hopper lid. The auger will not run with the
hopper door open.
Once the auger is primed pressing ENTER will start the
electronicignitionsequence.Note:Preloadingtherepot
isn’t necessary for electric ignition; the program is designed
toautomaticallyloadtherepot.Thenoisesyouwillhear
during electric ignition are the combustion fan and air pump
running.Thescreenwillreadasfollows:
ELECTRIC IGNITE
LEVEL 1
STARTING FIRE AND ELECTRIC IGNITE
SCREENS
(MF3800 only)
The starting re and electric ignition sequences have
been designed to take a cold stove up to normal operating
temperature. These are preset feed rates and fans speeds
set by CSW to ensure the ignition of multiple types of
fuels.
During starting re andelectric ignition sequences you
may change the level by pressing the TEMP UP or TEMP
DOWN buttons.
Duringstartingreandelectricignitionsequencesyoumay
choose to run your stove thermostatically by pressing the
THERMOSTAT ON/OFF button. See Thermostatic Control
Operation.
Atanytimeyoumayaddmorefueltotherepotbypressing
theADDFUELbutton.Note:thefeedaugerwillstayon
for one minute or until the ADD FUEL button is pressed
again.
During starting re and electric ignition sequences the
convectionfan(thefanthatcirculateswarmairthroughout
room)willstartoncestovehasreached110degrees.To
control convection fan speed use Fan Up and Fan Down
buttons(Buttons3and8inFigure22).Note:Hotstoves
need air circulating through them at all times to prevent
overheating the electronic controls. Therefore, once proof
ofreismadetheconvectionfanwillcontinuetorun.
After the stove runs it’s startingre or electric ignition
sequences the controller will read RANGE 1-4(willdisplay
chosenfuelrange)LEVEL 1-6(willdisplaychosenheat
outputlevel).Thisisthenormaloperatingscreensforthe
MF series parlor stove.
NORMAL OPERATION
During normal manual operation of the stove the controller
will read asfollows:
TEMP 72
RANGE1-4LEVEL1-6
At any time during normal operation you will be able to
change the Fuel Range by pressing the SCROLL button.
(MF 3800 only)Atanytimeduringnormaloperationyouwill
be able to run the igniter by pressing the SCROLL button
during the normal operating
At anytime during normal operation you may change the
heat level by pressing the TEMP UP or TEMP DOWN
buttons.Note:ifthestoveisbeingcontrolledbythelocal
thermostat the TEMP UP and TEMP DOWN buttons control
the thermostat setpoint. If the stove is being controlled
by the remote thermostat the TEMP UP or TEMP DOWN
buttons have no effect on the heat output.
At anytime during normal operation you may turn on or off
the thermostatic control by pressing the THERMOSTAT
ON/OFF button.