Filter
Top Products
14
UV36RN/RP Vent-Free Gas Fireplaces
20007436
T150
fireplace
control panel
11/6/03 djt
Valve Control
ON/OFF/PILOT
HI/LO Flame
Adjustment
ON/OFF
Switch
Piezo
NOTE: Optional Remote Control
Receiver May be Placed on Floor
Behind Cover Panel
Optional Gas
Shutoff Valve
T150
Fig. 15 Fireplace control panel.
WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage,
personal injury or loss of life.
A. This appliance has a pilot which must be lighted by hand.
When lighting the pilot, follow these instructions exactly.
B. BEFORE OPERATION smell all around the appliance area
for gas. Be sure to smell next to the floor because some
gas is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any tele-
phone in your building.
• Immediately call your gas supplier from a neighbor’s tele-
phone.
• Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire depart-
ment.
C. Use only your hand to push in or turn the gas control knob.
Never use tools. If the knob will not push in or turn by
hand, don’t try to repair it. Call a qualified service techni-
cian. Force or attempted repair may cause a fire or an
explosion.
D. Do not use this appliance if any part of it has been under
water. Immediately call a qualified service technician to
inspect the appliance and to replace any part of the control
system or gas control which has been under water.
E. Be sure both the receiver and the remote have had a 9 volt
battery installed in each.
Lighting Instructions
1. STOP! Read the safety information above before proceed-
ing.
2. Refer to Figure 16. To turn off
the gas supply, depress the knob
slightly and turn clockwise
to the OFF position.
3. Wait five (5) minutes to clear out
any gas. Then smell for gas,
including near the floor. If you
smell gas, STOP! Follow “B” in
the safety information above. If
you don’t smell gas, go to the
next step.
4. Refer to Figure 17. Locate the
pilot. It is at the right side of the
burner.
5. Refer to Figure 18. Push in the
control knob and turn counter-
clockwise to the PILOT position. Hold the control
knob in for a few seconds.
6. While still holding in the control knob, press the ignitor push-
button several times. This will cause a spark at the pilot
which will ignite the pilot gas. (Fig. 19)
7. Hold the control knob for 60 seconds to prevent the flame
failure detector from shutting off the
gas while its probe is warming up.
8. Release the control knob.
• If the knob does not pop up when
released, stop and immediately call
your service technician.
• If the pilot will not stay lit after sev-
eral tries, turn the gas control knob to
OFF and call your service technician
or gas supplier.
9. Refer to Figure 20. When the
pilot remains lit, turn the control
knob counterclockwise to
the ON position.
10. Lighting Instructions for Millivolt
Wall Switch. After the pilot is lit
and the control knob is released,
the wall switch can be switched
to turn the unit “ON” or switched
to turn it “OFF”. Refer to Page 13 for wiring.
T118
Lighting Instr
Piezo
10/28/03 djt
Fig. 19
Piezo
T125
OP Pilot
10/28/03 djt
Fig. 17
OFF
ON
PILOT
OFF
ON
PILOT
OFF
ON
PILOT
T151
control knob
11/6/03 djt
Fig. 16 Fig. 18 Fig. 20
To Turn OFF Gas to Appliance
Depress the control knob slightly and turn it clockwise to the OFF position. Refer to Figure 16.
For Your Safety, Read Before Lighting