Filter
Top Products
4
Aspen Woodburning Stove
30000369
Chimneys
Your stove must be connected either to a sound
masonry chimney that meets local codes, to a relined
masonry chimney that meets local codes, or to an
approved prefabricated metal chimney. Whichever of
those types you use, the chimney and chimney connec-
tor must be in good condition and kept clean.
If you use an existing masonry chimney, it must be
inspected to ensure safe condition before the stove is
installed. Your local professional chimney sweep, build-
ing inspector, or fire department official will be able to
make the inspection or direct you to someone who can.
The chimney should extend at least 3’ (914 mm) above
the highest point where it passes through a roof, and at
least 2’ (610 mm) higher than any portion of a building
within 10’ (3 m).
To assure proper draft and good performance, any
chimney used with this stove should extend at least 16’
(4.9 m) above the flue collar of the stove.
SAFETY NOTICE: IF YOUR STOVE IS NOT PROP
-
ERLY INSTALLED, OPERATED AND MAINTAINED, A
HOUSE FIRE MAY RESULT. FOR SAFETY, FOLLOW
ALL INSTALLATION, OPERATION AND MAINTE-
NANCE DIRECTIONS. CONTACT LOCAL BUILDING
OFFICIALS ABOUT RESTRICTIONS AND INSTAL-
LATION INSPECTION REQUIREMENTS IN YOUR
AREA.
Before you begin an installation, review your plans to
be certain that:
• Your stove and chimney connector will be far enough
from combustible material to meet all clearance
requirements.
• The floor protector is large enough and is constructed
properly to meet all requirements.
• You have all necessary permits from local authorities.
Your local building official is the final authority for ap
-
proving your installation as safe and determining that it
meets local and state codes.
The metal label permanently attached to the back of
the stove indicates that the Aspen has been tested to
current UL and ULC standards by Intertek Testing Ser-
vices of Middleton, Wisconsin. Clearance and installa-
tion information is also printed on the label. Local au-
thorities generally will accept the label as evidence that,
when the stove is installed according to the information
on the label and in this manual, the installation meets
codes and can be approved. Codes, however, vary in
different areas. Before starting the installation, review
your plans with the local building authority. Your local
dealer can provide any additional information needed.
For any unresolved questions about installation, refer
to the National Fire Protection Association’s publication
ANSI/NFPA 211–1988 Standard for Chimneys, Fire-
places, Vents and Solid Fuel Burning Appliances. In
Canada, the equivalent publication is CSA CAN-B365,
Installation Code for Solid Fuel Burning Appliances and
Equipment. These standards are the bases for many
national codes. They are nationally recognized and are
accepted by most local authorities. Your local dealer
or your local building official may have a copy of these
regulations.
IMPORTANT:
Failure to follow these installation
instructions may result in a dangerous situation, in-
cluding a chimney or house fire. Follow all instruc-
tions exactly and do not allow makeshift compro-
mises to endanger property and personal safety.
Installation
Masonry Chimneys
An existing masonry chimney must be inspected to con-
firm that it has a lining. Do not use an unlined chimney.
The chimney also should be examined for cracks,
loose mortar, other signs of deterioration, and blockage.
Repair any defects before the chimney is used with
your stove.
2' Min.
2' Min.
3'
Min.
0 To 10'
3'
Min.
0 To 10'
AC617
RLTSKC8
2/11/98
Fig. 2 The 2’-3’-10’ Chimney Rule.
Reference Point
AC617
ST241
chimney types
12/13/99 djt
Fig. 3 Standard Chimney Types
A prefabricated double-
wall insulated chimney
A tile-lined
masonry
chimney
ST241