Filter
Top Products
Regency P48 Zero Clearance Direct Vent Gas Fireplace
36
Copy of the Lighting Plate Instructions
NORMAL OPERATING
SOUNDS OF
GAS APPLIANCES
It is possible that you will hear some sounds
from your gas appliance. This is perfectly
normal due to the fact that there are various
gauges and types of steel used within your
appliance. Listed below are some examples. All
are normal operating sounds and should
not be considered as defects in your appliance.
Blower:
Regency gas appliances use high tech blow-
ers to push heated air farther into the room. It
is not unusual for the fan to make a "whirring"
sound when ON. This sound will increase or
decrease in volume depending on the speed
setting of your fan speed control.
Burner Tray:
The burner tray is positioned directly under the
burner tube and logs and is made of a different
gauge material from the rest of the firebox and
body. Therefore, the varying thicknesses of
steel will expand and contract at slightly differ-
ent rates which can cause "ticking" and "crack-
ing" sounds. You should also be aware that as
there are temperature changes within the unit
these sounds will likely re-occur. Again, this is
normal for steel fireboxes.
Blower Thermodisc:
When this thermally activated switch turns ON
it will create a small "clicking" sound. This is the
switch contacts closing and is normal.
Pilot Flame:
While the pilot flame is on it can make a very
slight "whisper" sound.
Gas Control Valve:
As the gas control valve turns ON and OFF, a
dull clicking sound may be audible, this is normal
operation of a gas regulator or valve.
Unit Body/Firebox:
Different types and thicknesses of steel will
expand and contract at different rates resulting
in some "cracking" and "ticking" sounds will be
heard throughout the cycling process.
OPERATING INSTRUCTIONS
TO TURN OFF GAS APPLIANCE
FOR YOUR SAFETY READ BEFORE LIGHTING
4) Push in control knob all the way and
hold in. Continually push and release
the black button on spark igniter until
pilot lights. Continue to hold the
control knob in for about 1/2 minute
after the pilot is lit. Release knob and
it will pop back up. Pilot should remain
lit. If it goes out, repeat steps 1) to 4).
If knob does not pop up when
released, stop and immediately call
your service technician or gas
supplier. If the pilot will not stay lit
after several tries, turn the gas control
knob to “OFF” and call your service
STOP! Read the safety information
above on this label.
1)Push in gas control knob slightly
and turn clockwise to “OFF”.
Knob cannot be turned from “PI-
LOT” to “OFF” unless knob is pushed
in slightly. Do not force.
2) Wait five (5) minutes to clear out any
gas. If you then smell gas STOP!
Follow step “B” in the Safety Infor-
mation above on this label. If you
don’t smell gas, go to the next step.
3) Turn knob on gas control counter-
clockwise to“PILOT”.
1) Push in the gas control knob slightly and turn clockwise to “OFF”. Do not force.
2) Turn off all electric power to the appliance if service is to be performed.
CAUTION: Hot while in operation. Do not touch. Severe Burns may result. Due
to high surface temperatures keep children, clothing and furniture, gasoline
and other liquids having flammable vapors away. Keep burner and control
compartment clean. See installation and operating instructions
accompanying appliance.
LIGHTING INSTRUCTIONS
technician or gas
supplier.
5)Turn gas control knob
counterclock-wise
to “ON”.
6)Use rocker switch to
operate main burner.
A)This appliance has a pilot which
must be lighted by hand. When
lighting the pilot, follow these
instructions exactly.
B)BEFORE LIGHTING smell all around
the appliance area for gas. Be sure
to smell next to the floor because
some gas is heavier than air and
will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
- Do not try to light any appliance.
- Do not touch any electric switch, do
not use any phone in your building.
- Immediately call your gas supplier
from a neighbours phone. Follow
the gas supplier’s instructions.
- If you cannot reach your gas
supplier, call the fire department.
C)Use only your hand to push in or turn
the gas control knob. Never use tools.
If the knob will not push in or turn by
hand, don’t try to repair it, call a
qualified service technician. Force or
attempted repair may result in a fire
or explosion.
D)Do not use this appliance if any part
has been under water. Immediately
call a qualified service technician to
inspect the appliance and to replace
any part of the control system and any
gas control which has been under
water.
E) This appliance needs fresh air for
safe operation and must be installed
so there are provisions for adequate
combustion and ventilation air.
DO NOT REMOVE THIS INSTRUCTION PLATE
WARNING: If you do not follow these instructions exactly, a fire or
explosion may result causing property damage, personal injury or loss
of life. Improper installation, adjustment, alteration, service or maintenance
can cause injury or property damage. Refer to the owner’s information
manual provided with this appliance. For assistance or additional
information consult a qualified installer, service agency or gas supplier.
OFF
ELEMENT
THERMO-
ELECTRIQUE
VEILLEUSE
PILOT BURNER
THERMOPILE
908-017b
You may shut off the pilot during prolonged non use periods to conserve fuel.
This appliance must be installed in accordance with local codes, if any; if none, follow the
National Fuel Gas Code, ANSI Z223.1/NFPA 54, or Natural Gas and Propane Installation
Codes, CSA B149.1. (Australia: AG601, New Zealand: NZS 5261)