Napoleon Fireplaces GD80PT Indoor Fireplace User Manual


 
22
W415-0447 / B / 05.24.05
The timer setting is used to maintain the desired room
temperature for a specific length of time (1 to 120 minutes)
that you want the fireplace to operate.
Press the TIMER button once. The LCD will blink "_ _ _".
Adjust the time using the up or down arrow keys. (The LCD
displays the time chosen.) Press the TIMER button to engage
the timer. (When time has expired, the LCD switches to off
and displays "_ _ _".)
1. With “Auto” displayed, pushing the button marked "flame
height" will display a flame image and the current flame
setting.
2. Use “UP” “DOWN” buttons to choose 3 different flame
levels:1,2,3.
1. Pushing the button marked "fan speed" will display a fan
image.
2. Use “UP” “DOWN” buttons to choose 3 different fan lev-
els:1,2,3.
1. Remove the cover on the back of the
remote transmitter to expose the code
switches. Slide the code switches to your
choice of ON or OFF positions. Factory
settings are all "OFF".
2. Remove power from the remote
receiver by unplugging the power cord or turning power off
at the circuit breaker.
3. Take the remote transmitter close to the remote receiver
(less than 5 feet from the remote receiver is recommended).
4. Turn on the remote receiver.
5. Install fresh AAA alkaline batteries into the remote trans-
mitter. The LCD on the remote transmitter will blink.
6. Press a button on the remote transmitter. The remote re-
ceiver will produce a "beep" sound when it receives the code
from the remote transmitter.
7. If you do not hear a "beep" sound from the remote receiver,
remove batteries from the remote transmitter and power from
the remote receiver. Wait for 1 minute and repeat steps 3 to
6.
8. Replace the cover of the remote transmitter and the
receiver. The system is now ready to operate.
9. If you desire to operate multiple remote receivers with
one remote transmitter, continue to hold the button on the
remote transmitter as you bring the remote transmitter within
5 feet of each remote receiver then slide the switch on the
remote receivers to ON position. Each will acknowledge
receipt of coding with a beep.
When used in this mode, the remote transmitter will work
normally but the buttons will be disabled.
Remove the cover at the back of the Remote Transmitter to
expose the Child-Proof switch. To activate this function, slide
the switch to the position marked C/P. "*Child-Proof*" will
appear on the LCD.
1. Turns accent light on/off.
2. Turns gas flame on/off.
3. Activates gas flame
adjustment.
4. Activates fan adjustment.
5. Adjusts options #3 & #4up.
6. Sets the timer.
7. Adjusts options #3 & #4 down.
8. Sets the time.
To operate the gas fireplace, the pilot needs to be running
and the gas valve turned to the on position.
You can run the fireplace on manual or remote.
When operating the main burner on manual without
power, the fireplace will operate on low input only.
Turn the main power switch to
manual to operate the gas features
of the fireplace in the event of a
power failure.
Turn the main power switches to
remote to operate with the gas and
the electric features of the fireplace
with the remote or thermostat.
With power, the manual position
operates the same as the remote position with the exception
of the ability to turn off the gas.
Turn the main power switch to the off position to disable both
the gas and the electric features of the fireplace.
To configure the remote transmitter to the receiver, see
“Privacy Code”.
OPERATION / MAINTENANCE
FIREPLACE OPERATION
HAND HELD REMOTE OPERATION
FIGURE 50
Thermostatic control automatically cycles the fireplace on and
off to maintain the desired room temperature. To turn the
fireplace burner on, press the gas button. The LCD will display
the “Auto” / “OFF” status. Set the desired room temperature
using the up or down arrow keys. If the temperature of
the room exceeds the set temperature, the
thermostat will automatically turn
the fireplace
off.
Note: If a blower is connected, the thermostatic control will
also turn off the blower when the fireplace is turned off.
Press and hold the CLOCK button until the hour flashes.
Adjust the hour using the up or down keys. Press the CLOCK
button again to confirm the hour and change to minutes.
Again, adjust the minutes using the up or down keys. Finally,
press the CLOCK button twice to confirm the settings and
return to normal, operating mode.
CODE SWITCHES
MANUAL / THERMOSTAT OPERATION
TO SET THE TIME
TIMER OPERATION
FLAME HEIGHT
FAN SPEED
PRIVACY CODE
CHILD-PROOF FUNCTION
FIGURE 49