Filter
Top Products
7
Expansion Valve Recommendations
-10°F. Suction 10° TD -15°F. Suction 15° TD
Model BTUH R-404 BTUH R-404A
Size 10° TD Alco Sporlan 15° TD Alco Sporlan
09 900 1350
12 1200 HFS
1
/
8
SZ EFS
1
/
8
Z 1800 HFS
1
/
8
SZ EFS
1
/
8
Z
16 1600 2400
21 2100 3150 HFS
1
/
4
SZ EFS
1
/
6
Z
28 2800 HFS
1
/
4
SZ EFS
1
/
6
Z 4200 HFS
1
/
2
SZ EFS
1
/
4
Z
35* 3500 HFES
1
/
4
SZ EFSE
1
/
4
Z 5250 HFES
1
/
2
SZ EFSE
1
/
2
Z
53* 5300 HFES
1
/
2
SZ EFSE
1
/
2
Z 7950 HFES1SZ EFSE1Z
*Sizes 35 and 53 use external equalized valves.
Dimensional Diagram
Thin Profile Electric Defrost Unit Cooler
Mounting
This unit cooler is designed for mounting from the top of the cooler. Drill holes for screws in accordance with mounting
dimensions given in Dimensional Diagram and Data.
After unpacking the unit, remove the fan panel and arrange the rear brackets as shown in the drawing. Insert the
screws for mounting the rear brackets into the top of the cooler cabinet. Slip the rear brackets, attached to the unit,
between the screw head and cabinet and secure in place. Install the front mounting screws. For proper drainage, the
unit should be installed level.
Thin Profile Vintage
Electric Defrost
Size A = 115-1-60
B = 208/230-1-60
NOMENCLATURE
TL 12 A G
Dimensional Data
Connections (In.)
Approx.
Dimensions (In.) Coil
Ship Wt.
Size A B C D E F H J K L M N W Inlet Suction Drain (Lbs.)
09 14
5
/
8
14
15
/
16
13
1
/
2
10
1
/
2
11
3
/
8
4
1
/
2
8
7
/
8
2
1
/
2
15
/
16
4
3
/
8
- 16
1
/
2
3
/
8
OD
3
/
8
ID
1
/
2
OD 14
12 18
5
/
8
14
15
/
16
13
1
/
2
10
1
/
8
10
1
/
4
4
1
/
2
8
3
/
8
9
1
/
2
15
/
16
4
3
/
8
- 20
1
/
2
3
/
8
OD
1
/
2
ID
1
/
2
OD 19
16 22
1
/
8
15
15
/
16
14
1
/
2
11
1
/
8
12 4
1
/
2
9
3
/
8
11
1
/
4
15
/
16
4
3
/
8
- 24
3
/
8
OD
1
/
2
ID
1
/
2
OD 23
21 22
1
/
8
16
1
/
2
15
/
16
16
1
/
2
14
1
/
2
18
7
/
8
6
3
/
4
11
7
/
8
17
1
/
4
15
/
16
4
3
/
8
- 24
3
/
8
OD
1
/
2
ID
1
/
2
OD 24
28 29
3
/
4
15
15
/
16
14
1
/
2
13 20
3
/
4
6
3
/
4
9
3
/
4
9
7
/
8
15
/
16
4
3
/
8
- 31
5
/
8
3
/
8
OD
1
/
2
ID
1
/
2
OD 27
35 35
3
/
4
16
1
/
2
1
5
/
16
16
1
/
2
14
1
/
2
33
1
/
4
6
3
/
4
11
5
/
8
18
3
/
8
1
5
/
16
6” 5
1
/
8
38
3
/
8
1
/
2
OD
5
/
8
ID
1
/
2
OD 38
53 46
1
/
2
16
1
/
2
1
1
/
8
16
1
/
2
14
1
/
2
44 6
3
/
4
11
5
/
8
30
3
/
8
1
1
/
2
6” 5
1
/
8
49
1
/
8
1
/
2
OD
7
/
8
ID
1
/
2
OD 53
FOR FOOD
SERVICE
INSTALLATIONS
. . . seal any joint
between unit cooler
and cooler liner
with a sealant
listed by the
National Sanitation
Foundation,
Standard 51