Filter
Top Products
Upholstery Brush
The upholstery brush is conveniently
mounted on the back of the main body
of the vacuum cleaner. The brush can
be used for cleaning the furniture,
Venetian blinds, books, lamp shades
and shelves. (Fig. 14)
Extension Tube
This attachment is stored on the right
side of the cleaner on it’s own holder in
front of where the flexible hose ttaches
to the hose connector. This tool is
designed to extend your reach. Attach
this accessory by it’s narrower end to
the flexible hose and use for hard to
reach places. (Fig. 15)
Turbo Brush
The turbo brush conveniently attaches
to the handle with an attaching bracket.
1. Ensure that the handle is attached
to the main body before attaching
the turbo brush to the handle.
2. First attach the turbo brush to the
attaching bracket by hooking the
edge of the opening under the
trapdoor on the bottom of the turbo
brush to the flat part of the bracket.
Then press the tube part of the
turbo brush against the clip on the
bracket until the two pieces snap
together.
3. Hold the assembled pieces by the
turbo brush and touch the two clips
on the bracket to
the metal tube of
the handle. Hold
the handle from
the top and
squeeze the two
pieces together,
putting more
force on the
bigger clip until
the bracket
snaps on.
4. Remove the turbo
brush from the
bracket in order to
use. (Fig. 16)
Fig. 14
Fig. 12
Fig. 13
Fig. 15
Fig. 16
OPERATING INSTRUCTIONS
Cleaning the Pre-Motor Filter
1. Pull the pre-motor filter frame out of
the main body. (Fig. 11)
2. Remove the pre-motor filter from the
frame and wash both the filter and
the frame under the tap with
lukewarm water. (Fig. 12)
3. Allow both parts to air dry
completely before placing the filter
back in the frame and sliding the
frame back into the main body. Let
the pre-motor filter and pre-motor
filter frame air dry for 24 hours. DO
NOT DRY IN THE DRYER.
Using the Accessories
IMPORTANT: Make sure the vacuum
cleaner is turned off when attaching or
removing any accessories.
CAUTION:DO NOTpull the vacuum
cleaner around by the hose. DO NOT
over stretch the hose. Trying to reach
beyond the hose’s extent may cause
the vacuum cleaner to tip over.
Crevice Tool
The crevice tool is located inside the
extension tube and can be used for
radiators, crevices, corners,
baseboards and between cushions.
(Fig. 13)
7
Fig. 11
The efficiency of your turbo brush
depends on the bristle brush rotating at
high speed. Strong air suction is needed
to accomplish this. In order to ensure
that maximum air suction is maintained,
please read the following instructions:
1. Empty the dust cup frequently
during use.
2. Inspect the rotating bristle brush
and air turbine wheel regularly.
Inspect the turbine wheel and air
passage for debris and/or blockages.
Remove debris if present.
3. Inspect the rotating brush for a build
up hair or string. If present, remove
by carefully cutting with scissors.
Avoid damaging or cutting the
bristles.
Cleaning the Pet Hair Turbo Brush
To clean the pet hair turbo brush:
1. Hold the turbo brush in your hand
and with the help of a screwdriver,
gently pry the cover off. (Fig. 17)
OPERATING INSTRUCTIONS
8
Using the Vacuum for Above
Floor Cleaning
1. Place the vacuum cleaner in the
upright position.
2. Set the carpet height adjustment
knob to the highest setting “ ”.
3. To attach the accessories to the
flexible hose, remove the hose from
the hose connector and push the
desired accessory onto the end.
4. If additional length is required, the
handle may be used. Remove the
handle from the main body by first
lifting the handle locking lever. Push
the end of the flexible hose into the
opening at the back of the handle.
Attach the desired accessory to the
end of the handle.
5. The crevice tool, turbo brush and
upholstery brush can also be
attached to the end of the extension
tube.
6. Ensure that the attachment you are
using is appropriate for the surface
you are cleaning.
7. To return to vacuuming the floor,
perform the following steps:
• Detach the hose from the handle
and push it snugly back into the
hose connector.
• Hang the flexible hose back onto
the hose holder.
• Return the handle to it’s regular
position in the opening on top of
the main body and push down the
handle locking lever to lock the
handle into place.
• Return the carpet height
adjustment knob to the appropriate
setting.
2. Inspect turbine wheel and air
passage for debris and/or blockage.
Remove any debris if present.
3. Inspect the rotating brush for built-up
hair or string. If present, remove by
carefully cutting with scissors. Avoid
damaging or cutting bristles.
4. Once clean, align the cover of the
turbo brush with the edge of the
brush and snap it closed. (Fig. 18)
Fig. 17
Fig. 18