Filter
Top Products
107032-01F
For more information, visit www.desatech.com
For more information, visit www.desatech.com
26
GWMT1 WALL MOUNTED
THERMOSTAT (OPTIONAL)
Make sure the heater switch is on AUTO and set the temperature
adjustment on wall thermostat to the desired setting. The ther-
mostat has been electronically calibrated at the factory and
requires no adjustment or leveling.
Upon installation, the thermostat must be allowed to stabilize at
room temperature for a minimum of 30 minutes for proper
operation. See installation instructions on page 21 of this manual.
OPERATING FIREPLACE
Continued
Note:
All remote control accessories must be purchased sepa-
rately (see Accessories, pages 38 and 39). Follow instructions
included with the remote control.
Thermostat Control Operation
(Optional GHRCTA Series Only) The thermostat control set-
ting on the remote control unit can be set to any comfort level
between WARMER and COOLER. The burners will turn on
and off automatically to maintain the comfort level you select.
The ideal comfort setting will vary by household depending
upon the amount of space to be heated, the output of the central
heating system, etc.
For wall thermostat operation, follow instruction supplied with
thermostat accessory GWMT1. For wall switch operation fol-
low instructions supplied with GWMS2.
OPTIONAL REMOTE
OPERATION
NOTICE: You must light the pilot before using the remote
control unit. See
Lighting Instructions
on page 25.
1. After lighting, let pilot flame burn for about one minute.
Turn control knob to ON position. Adjust flame adjust-
ment knob anywhere between HI and LO. Slide the selec-
tor switch to the REMOTE position.
Note:
The burner may
light if hand-held remote ON button was on when selector
switch was last turned off. You can now turn the burner on
and off with the hand-held remote control unit.
IMPORTANT:
Do not leave the selector switch in the RE-
MOTE or ON position when the pilot is not lit. This will
drain the battery.
IMPORTANT:
Be sure to press the ON/OFF buttons on the
hand held remote control unit for up to 3 seconds to assure
proper operation.
GHRC Series Operation:
2a. Press the ON/OFF button to turn the burners on and off.
When turning burners off, the pilot will remain lit.
OPERATING FIREPLACE (REMOTE-READY MODELS)
Optional Remote Operation
GWMT1 Wall Mounted Thermostat (Optional)
Figure 52- Setting the Selector switch, Control Knob, and Flame
Adjustment Knob for Remote Operation
Figure 53 - Thermostat Hand-Held Remote Control Unit
Selections (GHRCTA Only)
Increases Room
Temperature in
AUTO Mode
Decreases
Room
Temperature in
AUTO Mode
Turns Burners
On or Off and
Allows You to
Choose the Auto
Setting
Shows
Temperature
Setting
The Log
Fireplace will
Automatically
Cycle between
Pilot and the
Heat Setting
that has been
Selected
GHRCTA Series Operation:
2b. Press the AUTO/ON/OFF button on the hand-held remote
control (see Figure 53). The lights to the left of the button
will show AUTO, ON, or OFF.
• In the ON mode, the burners will ignite. The fireplace is
in manual mode when ON is lit.
• In the AUTO mode, the thermostat in the hand-held re-
mote unit controls the room temperature. To increase the
room temperature, press the top arrow of the TEMP but-
ton. To lower the room temperature, press the bottom ar-
row of the TEMP button. At higher settings the fireplace
will run longer.
IMPORTANT:
This remote control has been specially engi-
neered to take an air temperature sample every 5.5 minutes
in the auto mode. It will not respond immediately to the tem-
perature setting being turned up or down.
IMPORTANT:
The hand-held remote control unit must be
near the fireplace. Do not keep the hand-held remote con-
trol unit too close to the fireplace. The thermostat on the
hand-held remote control unit will heat up too quickly and
turn the fireplace off.
3. To turn the burner off, press the AUTO/ON/OFF button un-
til OFF lights. The pilot will remain lit.
IMPORTANT:
To turn the pilot off, manually turn the con-
trol knob on the heater to the OFF position.
O
F
F
P
I
L
O
T
O
N
L
O
I
H
REMOTE
OFF
ON
Flame Adjustment Knob
Control Knob
Selector Switch in Remote
Position (Optional Remote Control)