Beckett FII 85 Burner User Manual


 
RWB 6104 BAFII R01 Page 5
General Speci cation
Table 1 – Burner Speci cations
Capacity ‘HLX’ Heads
Firing rate: - 0.40 – 1.50 GPH
Input: Min./Max - 56,000 /210,000 Btu/h
‘FBX’ Heads
Firing rate: - 0.40 – 1.35 GPH
Input: Min./Max. - 56,000/189,000 Btu/h
Certi cation/
Approvals
UL certi ed to comply with ANSI/UL296 &
tested to CSA B140.0
Fuels U. S No. 1 or No. 2 heating oil only (ASTM
D396)
Canada No. 1 stove oil or No. 2 furnace oil
only
Electrical Power supply - 120 volts AC, 60 Hz, single
phase
Operating load - 5.8 Amps max
Motor - 1/7 hp, 3450 rpm, NEMA 48M
frame PSC rotation CCW when
facing shaft end
Ignition - Continuous duty solid-state igniter
Fuel pump Outlet pressure - Note 1
Air tube ATC code - See Table 2
Dimensions
(with cover)
Height (maximum) - 13 inches
Width (maximum) - 14 inches
Depth - 6-11/16 inches
Air tube diameter - 3-1/2 inches
*Note 1. See appliance manufacturer’s burner speci cations for
recommended outlet pressure.
Notice Special Requirements
For recommended installation practice in Canada,
refer to the latest version of CSA Standard B139 &
B140.
Concealed damage — If you discover damage to
the burner or controls during unpacking, notify the
carrier at once and le the appropriate claim.
When contacting Beckett for service information —
Please record the burner serial number (and have
available when calling or writing). You will nd the
serial number on the silver label located on the left
rear of the burner. Refer to Figure 1.
Inspect/Prepare Installation Site
Clearances to Burner and Appliance
Provide space around burner and appliance for
ease of service and maintenance. Check the mini-
mum clearances against those shown by the ap-
pliance manufacturer and by applicable building
codes.
General Information
Table 2 – Air Tube Combinations (ATC) & Dimensions
ATC codes for usable air tube lengths dim. “A” (Figure 3) Firing rate range (gph)Min-Max
3” 5” 7” 9” ATC Code Head AFII 85 AFII 100 AFII 150
Adjustable
w/stop
screw Head
Design
HLX30 HLX50 HLX70 HLX90 HB AF2-6 0.4-0.85 gph 0.65-1.00 gph 0.75-1.35 gph
HLX30 HLX50 HLX70 HLX90 HC AF2-9 N/A 0.65-1.00 gph 0.75-1.50 gph
HLX30 HLX50 HLX70 HLX90 HD AF2-6 0.40-0.85 gph 0.65-1.00 gph 0.75-1.10 gph
HLX30 HLX50 HLX70 HLX90 HE AF2-9 N/A 0.65-1.00 gph 0.75-1.35 gph
Head Design
- Fixed
FBX30 FBX50 FBX70 FBX90 HFXS FB0 0.40-0.65 gph 0.55-0.75 gph 0.75-1.00 gph
FBX30 FBX50 FBX70 FBX90 HGXS FB3 0.55-0.85 gph 0.55-1.10 gph 0.85-1.20 gph
FBX30 FBX50 FBX70 FBX90 HHXS FB4 N/A 0.75-1.10 gph 1.10-1.25 gph
FBX30 FBX50 FBX70 FBX90 HIXS FB6 N/A 0.85-1.15 gph 1.15-1.35 gph
HB 6 slot
HC 9 slot
HD 6 slot
HE 9 slot