Filter
Top Products
14
TEMPERATURE REGULATION
CAUTION
THIS WATER HEATER IS EQUIPPED WITH AN ADJUSTABLE
THERMOSTAT TO CONTROL WATER TEMPERATURE. HOT
WATER TEMPERATURES REQUIRED FOR AUTOMATIC
DISHWASHER AND LAUNDRY USE CAN CAUSE PAINFUL
SCALDING WITH POSSIBLE SERIOUS AND PERMANENT
INJURY. THE TEMPERATURE AT WHICH INJURY OCCURS
VARIES WITH THE PERSON'S AGE AND THE TIME OF
EXPOSURE. THE SLOWER RESPONSE TIME OF CHILDREN,
AGED OR DISABLED PERSONS INCREASES THE HAZARDS
TO THEM. NEVER ALLOW SMALL CHILDREN TO USE A HOT
WATER TAP OR TO DRAW THEIR OWN BATH WATER. NEVER
LEAVE A CHILD OR DISABLED PERSON UNATTENDED IN A
BATHTUB OR SHOWER.
THE WATER HEATER SHOULD BE LOCATED IN AN AREA
WHERE THE GENERAL PUBLIC DOES NOT HAVE ACCESS.
It is recommended that lower water temperatures be used to
avoid the risk of scalding. It is further recommended, in all cases,
that the water temperature be set for the lowest temperature
which satisfies your hot water needs. This will also provide the
most energy efficient operation of the water heater. The water
temperature adjustment was factory set at the lowest
temperature. Pressing the "COOLER"
button decreases
temperature and pressing the "HOTTER"
button increases
the temperature.
SETTING THE WATER HEATER TEMPERATURE AT 120°F
(APPROX. "
" MARK ON TEMPERATURE SETTING OF
CONTROL) WILL REDUCE THE RISK OF SCALDS.
Some
states require settings at specific lower temperatures.
Figure 10 shows the approximate water temperatures produced
at various thermostat settings. Short repeated heating cycles
caused by small hot water uses can cause temperatures at the
point of use to exceed the thermostat setting by up to 30°F. If you
experience this type of use you should consider using lower
temperature settings to reduce scald hazards.
Valves for reducing the
point-of-use temperature by mixing cold
and hot water are available. See figure 2. Also available are
inexpensive devices that attach to faucets to limit hot water
temperatures.
Contact a licensed plumber or the local plumbing
authority.
To avoid any unintentional changes in water temperature
settings, the control has a tamper resistant feature for changing
the temperature setting. To change the temperature setting follow
these instructions:
TEMPERATURE INDICATORS
TEMPERATURE ADJUSTMENT BUTTONS
1. "Wake Up" the temperature indicators by holding down both
the "COOLER" and "HOTTER" temperature adjustment
buttons at the same time for one second (see Figure 10).
One or two of the temperature indicators will light up. These
indicators will only remain on for 30 seconds if no further
buttons are pressed. After 30 seconds the control will go
back to "Sleep" mode.
2. Release both of the temperature adjustment buttons.
A. To decrease the temperature press and release the
"COOLER" button until desired setting is reached.
B. To increase the temperature press and release the
"HOTTER" button until the desired setting is reached.
NOTE: Holding down the button will not continue to lower or
raise the temperature setting. The button must be pressed and
released for each temperature change desired.
SHOULD OVERHEATING OCCUR OR THE GAS SUPPLY FAIL
TO SHUT OFF, TURN OFF THE MAIN MANUAL GAS SHUTOFF
VALVE TO THE APPLIANCE. SEE FIGURE 1 (G).
Time to Produce
Display 2nd & 3rd Degree
Temperature Setting A B C Burns on Adult Skin
C - Flashing = approx. 160°F About 1/2 seconds
C = approx. 150°F About 1-1/2 seconds
B = approx. 140°F Less than 5 seconds
A = approx. 130°F About 30 seconds
= approx. 120°F More than 5 minutes
WARM = approx. 80°F - - - - - - - - - - - - - - -
FIGURE 10
MAINTENANCE
CAUTION
DISCONNECT FROM ELECTRICAL SUPPLY BEFORE SERVICING
UNIT. FOR YOUR SAFETY, WATER HEATER SERVICE SHOULD BE