Filter
Top Products
43
“Low 24VAC” Voltage from transformer less than 18 vac Continuous Auto Reset
Check transformer output. Should be over 24vac. May be caused by
excessive current drain or a faulty transformer
“Brown Out Reset” Indicates a brown out reset occurred - - - - None
Caused by a momentary dip in voltage on the CCB +5vdc power bus. Contact factory. (Not considered a
serious problem if it only occurs on very rare occasions.)
“Timeout Reset” Indicates a watchdog reset occurred - - - - None
Caused when the micro executes the software in an improper way. Contact factory. (Not considered a
serious problem if it only occurs on very rare occasions.)
“FCB Comm Timeout” FCB did not receive command from CCB Continuous SOFT
Caused when communications between the CCB and the FCB are interrupted. May occur when a surge of
power on a nearby device (i.e. arc welder) creates an EMI burst. Not a serious problem if it occurs rarely.
“No Flow” Water is not flowing Continuous SOFT
Caused by the flow switch being open when it should be closed. Check water lines, pump, flow switch
contacts, wiring.
“Blower Prov Stg* Blower pressure is too low it they should have been closed. Continuous SOFT
Check blower, switch contact, wiring, and for air leaks.
“Blocked Flue” Flue is Blocked Continuous SOFT
Caused by the blocked flue switch contacts being open when they should have been closed. Check for flue
blockage, switch contacts, wiring.
“High Limit” Outlet temp. exceeded high limit setpoint Continuous Auto Reset
Caused when the temperature of the outlet probe exceeds the high limit setpoint. This is an internal
“software” limit switch and not an actual device. Check that the over temperature is not being caused by
improper setup or operation of the boiler.
“ECO fault” Outlet temp is too high Flashing HARD
Caused when the ECO (a thermostat) contacts in the Outlet probe are open when they should be closed.
Fault may be due to high outlet temperature, bad switch contacts in the ECO, or disconnected wiring. Note:
The ECO can be checked by disconnecting the outlet probe from the CCB and reading the resistance
across the two active pins on the connector at the end of the probe cable. The value should be approximately
0 ohms when the temperature of the probe is less than 220°F.
“Low Water” Water level is too low Flashing HARD
Caused by the Low Water Cut Out device not closing its feedback switch contacts when it should. Check
water line, switch contacts, wiring, LWCO.
“Low Gas” Gas pressure is too low Flashing HARD
Caused by the Low Gas switch being open when it should be closed. Check gas line, switch contacts,
wiring.
“IRI Gas” IRI Gas Valve did not turn on Flashing HARD
Caused by the IRI Gas Valve not closing its feedback switch contacts when it should. Could also be caused
by a problem with the relay output on the CCB. Check output to IRI Gas Valve, switch contacts, wiring.
“Powered Vent” Power vent not running Flashing HARD
Caused by the Powered Vent device not closing its feedback switch contacts when it should. Could also be
caused by a problem with the relay output on the CCB. Check output to powered vent, switch contacts, wiring.
“High Gas Stg*” Gas pressure too high Flashing HARD
Caused by the High Gas switch being open when it should be closed. Check gas line, switch contacts, wiring.
“Inlet Probe” Inlet probe shorted or open Flashing HARD
Caused when the thermistor in the probe or the wiring to the probe is shorted or disconnected. Check the
probe. Note: The thermistor and wiring can be checked by disconnecting the probe from the CCB and
reading the resistance across the two active pins on the connector at the end of the probe cable. The value
should be approximately 10K ohms (value will change slightly with changes in temperature).
“Outlet Probe:” Outlet probe shorted or open Flashing HARD
Caused when the thermistor in the probe or the wiring is shorted or disconnected. Check the probe. Note:
the thermistor and wiring can be checked by disconnecting the probe from the CCB and reading the
resistance across the two active pins on the connector at the end of the probe cable. The value should be
approximately 10K ohms (value will change slightly with changes in temperature).