Filter
Top Products
USER MANUAL
ENGLISH
146 2598 000(1)2005-03 A FLOORTEC R 360 P 13
SIDE BROOM HEIGHT CHECK AND
ADJUSTMENT
1. Check the side broom height from the ground,
proceeding as follows:
– Drive the machine on a level ground and lower the
side brooms.
– Keep the machine stationary and rotate the side
brooms for a few seconds.
– Lift the side brooms, then move the machine and
switch it off.
– Check if the size and orientation of the prints left
by the side brooms are as shown in the figure (1
and 2, Fig. J). In case the prints are not within
specifications, it is necessary to adjust the broom
height, proceeding as described in step 2 below.
2. Disengage the lever (4, Fig. C) and rotate the block
(33) clockwise or counterclockwise to adjust the
broom height from the ground.
3. Perform step 1 again to check the proper adjustment
of the side broom height from the ground.
4. When the brooms are too worn to be adjusted,
replace them as shown in the next paragraph.
SIDE BROOM REPLACEMENT
1. Drive the machine on a level ground and engage the
parking brake (7, Fig. C).
2. Turn the ignition switch (2, Fig. B) to “0” position.
3. Introduce the hand inside the side broom and press
the tabs (1, Fig. K) inwards, then remove the broom
(2) disengaging it from the four pins (3).
4. Install the new broom engaging it on the pins (3) and
on the tabs (1).
5. Carry out the side broom height check and
adjustment, as described in the previous paragraph.
DUST FILTER CLEANING AND INTEGRITY
CHECK
1. Drive the machine on a level ground and engage the
parking brake (7, Fig. C).
2. Turn the ignition switch (2, Fig. B) to “0” position.
3. Remove the hopper hook (21, Fig. C).
4. Remove the hopper (20) by using the handle (22, Fig.
C).
5. Turn the handle (1, Fig. L) downwards (90°
approximately) and let the filter frame (2) rotate
outwards.
6. Pull out the dust filter (3) upwards.
7. In an appropriate outdoor area, clean the filter
shaking it on a level and clean surface, tapping the
side (1, Fig. M) opposite the wire gauze (2). Complete
the cleaning by means of compressed air (3) of max.
6 bars, blowing only from the side protected by the
wire gauze (2), at a minimum distance of 30 cm (see
figure).
According to the filter type, observe the following
cautions:
– Paper filter (standard): Do not use water or
detergents to clean it not to irreparably damage
the filter.
– Polyester filter (optional): To clean it, see the
above-mentioned instructions. If necessary, for a
better cleaning, it is allowed to wash the filter with
water and non-lathering detergents. This provides
better quality cleaning but reduces the life of the
filter, which will have to be replaced more
frequently. The use of inadequate detergents can
damage the filter.
8. Check the filter body for tears.
9. If necessary, clean the filter compartment rubber seal
(4, Fig. L) along its perimeter and check it for integrity.
If necessary, replace it.
10. Reassemble in the reverse order of disassembly.
NOTE
Brooms of various hardness are available. This
procedure is applicable to all types of brooms.
NOTE
Brooms of various hardness are available. This
procedure is applicable to all types of brooms.
CAUTION!
It is advisable to use protective gloves
when replacing the side brooms because
there can be cutting debris between the
bristles.
NOTE
Besides the standard paper filter, polyester
filters are also available. The following
procedure is applicable to each type of filter.
NOTE
Reassemble the filter with the wire gauze (2,
Fig. M) facing the fan (19, Fig. U).