Initial settings
60
Initial settings
2
Select the size using CURSOR 2/3.
• Large: Large speaker(s) which can fully
reproduce the low-frequency range.
• Small: Small speaker(s) which can not fully
reproduce the low-frequency range.
• None: No speaker(s) connected.
If you set the front speakers to “Small”, you cannot
set the other speakers to “Large”.
Bass redirect
(available only when selecting EXPERT)
When you use small
speakers which do not fully
reproduce the low-
frequency range, you can
boost up the low-frequency
signal of the sub-woofer or
front speakers.
1
Select [BASS] using CURSOR 5/∞.
2
Select [S.woofer] or [L/R] using CURSOR
2/3.
• S.woofer: The low-frequency signal fed from the
sub-woofer output is boosted up.
• L/R: The low-frequency signals fed from
the front speaker outputs are boosted
up.
The “Bass redirect” setting is effective only when at least
any one of the speaker sizes is set to “Small”. If none of
them is set to “Small”, this setting is not activated
(“None” appears in the setting field).
Please note that the “L/R” setting is effective only when
playing back a Dolby Digital encoded DVD VIDEO disc.
If the front speaker size is set to “Small”, the Bass redirect
setting is fixed to “S.woofer”.
Speaker level
(available only when selecting EXPERT)
You can adjust the output
level of each speaker.
1
Select [LEVEL] using CURSOR 5/∞, then
press ENTER.
The color of “LEVEL” changes.
2
Select the desired speaker(s) to be set using
CURSOR 5/∞.
• F. S P : Front speakers. The level is fixed to 0dB.
• C.SP: Center speaker
• R.SP: Rear speakers
• S.WOOFER: Sub-woofer
The setting range is between –6dB and +6dB in 1dB
steps.
3
Set the level using CURSOR 2/3.
• For the speaker(s) whose size is set to “None”, the Speaker
level and Delay cannot be set (“—”appears in the setting
field).
• However, when playing back a Dolby Digital disc, LFE
signal is output from SUBWOOFER output even if
S. WOOFER shows “—”, allowing to activate a sub-woofer
connected. In such case, adjust the output level using the
level control on the sub-woofer.
Delay
(available only when selecting EXPERT)
You can adjust the delay
time of each speakers.
1
Select [DELAY] using CURSOR 5/∞, then
press ENTER.
The color of “DELAY” changes.
2
Select the desired speaker(s) to be set using
CURSOR 5/∞.
• F. S P : Front speakers. The delay is fixed to 0mS.
• C.SP: Center speaker (selectable from 0 to –5mS
in 1mS units)
• R.SP: Rear speakers (selectable from 0mS,
–5mS, –10mS, and –15mS)
3
Set the delay time using CURSOR 2/3.
• Delay of S.WOOFER cannot be set.
SPK.SETTING
EXPERT
LEVEL
DELAY
TEST TONE
F. SP
Large
C. SP
Small
R. SP
Small
S.woofer
BASS
PREFERENCE2PREFERENCE1
PRESS KEY
BASS
SPK.SETTING
EXPERT
LEVEL
DELAY
TEST TONE
F. SP
0dB
C. SP
0dB
R. SP
0dB
0dB
S.WOOFER
PREFERENCE2PREFERENCE1
PRESS KEY
BASS
NOTE
• To exit the speaker level (or delay) setting mode
Move
to [LEVEL] (or [DELAY]) in the on-screen display
and press ENTER until [LEVEL] (or [DELAY]) returns to
its original color.
SPK.SETTING
EXPERT
LEVEL
DELAY
TEST TONE
F. SP
0mS
C. SP
0mS
R. SP
0mS
0mS
S.WOOFER
PREFERENCE2PREFERENCE1
PRESS KEY
BASS
6$(1*ERRN3DJH7KXUVGD\$XJXVW30
