Initial settings
59
Initial settings
SCREEN SAVER
A television monitor screen may be burned out if a static
picture is displayed for a long time. To prevent this, the
unit automatically activates the screen saver function if a
static picture, such as an on-screen display or menu, is
displayed for over 5 minutes.
• MODE 1
The current picture gets
dark.
• MODE 2
The “screen saver” picture
appears and its brightness
changes.
• OFF
The screen saver function is off.
AV COMPULINK MODE
If you use the AV COMPU
LINK system, you must set
this item correctly.
Select from the three options:
“DVD1”, “DVD2” and “DVD3”
according to the equipment to
be connected.
See page 64.
Speaker Channel setting
Select the speaker
configuration type
according to your speaker
system. Normally, simply
select “5.1 CH.” or “2 CH.”.
However, by selecting
“EXPERT”, you can make
fine tuning to match your
speaker system.
• 2 CH.
When you connect to a 2-channel amplifier or TV.
• 5.1 CH.
When you connect to a 5.1-channel amplifier and use
the front, rear, center and sub-woofer speakers.
• EXPERT
When you want to make fine tuning to match your
speakers. The following five setting items are
available.
Speaker size settings
(available only when selecting EXPERT)
Sets the speaker sizes
according to your
speakers.
1
Select the speaker to be set using CURSOR
5/∞.
• F. S P :Front speakers
• C.SP: Center speaker
• R.SP: Rear speakers
NOTES
• The monitor screen of a projector or projection TV is
easily burned out if a static picture is displayed for a
long time. Be careful not to allow the monitor screen to
be burned out when you set the SCREEN SAVER mode
to “OFF”.
• The TV screen may be garbled when you set the
SCREEN SAVER mode to “MODE 1”. In this case, set to
another mode.
• When a static picture is displayed for a long time during
playback, the screen saver function is always activated
in “MODE 1” regardless of whether you select “MODE
1” or “MODE 2”.
PREFERENCE2PREFERENCE1 SPK. SETTING
DIGITAL AUDIO OUTPUT
STREAM/PCM
DOWN MIX
OFF
COMPRESSION
DTS BASS MANAGEMENT
OFF
OFF
AUTO STANDBY
OFF
SCREEN SAVER
PRESS KEY
MODE1
AV COMPULINK MODE
DVD1
PREFERENCE2PREFERENCE1 SPK. SETTING
DIGITAL AUDIO OUTPUT
STREAM/PCM
DOWN MIX
OFF
COMPRESSION
DTS BASS MANAGEMENT
OFF
OFF
AUTO STANDBY
OFF
SCREEN SAVER
PRESS KEY
MODE1
AV COMPULINK MODE
DVD1
Speaker setting
NOTES
• When selecting “5.1 CH.” or “EXPERT”, set “DOWN
MIX” to “OFF” (see page 58).
• The Dolby Digital LFE (Low Frequency Effect) signal is
always fed from the SUBWOOFER output on the rear
panel of the unit regardless of speaker setting.
• If you connect the unit's digital output to an external
Dolby Digital or DTS decoder (and set the “DIGITAL
AUDIO OUTPUT” option to “STREAM/PCM”), the
speaker setting above is not effective. Make the speaker
setting of the external decoder properly.
SPK.SETTING
5.1 CH.
LEVEL
DELAY
TEST TONE
F. SP
Large
C. SP
Small
R. SP
Small
S.woofer
BASS
PREFERENCE2PREFERENCE1
PRESS KEY
BASS
SPK.SETTING
EXPERT
LEVEL
DELAY
TEST TONE
F. SP
Large
C. SP
Small
R. SP
Small
S.woofer
BASS
PREFERENCE2PREFERENCE1
PRESS KEY
6$(1*ERRN3DJH7KXUVGD\$XJXVW30
