Filter
Top Products
9
REMOREMO
REMOREMO
REMO
TE SENSOR CONFIGURATE SENSOR CONFIGURA
TE SENSOR CONFIGURATE SENSOR CONFIGURA
TE SENSOR CONFIGURA
TION MENUTION MENU
TION MENUTION MENU
TION MENU
Installer Configuration MenuInstaller Configuration Menu
Installer Configuration MenuInstaller Configuration Menu
Installer Configuration Menu
Your thermostat is configured at the factory to recognize the remote sensor it is shipped with as indoor sensor A. The Installer
Configuration Menu is used only when adding or replacing a remote sensor or selecting a frequency offset.
Press
and buttons for a minimum of five seconds at the same time to enter the Installer menu. To scroll through
the menu items, momentarily press the
and buttons at the same time. To change the item option, press or
. To exit the menu scroll through all menu items. If no buttons are pushed for 3 minutes, the control will return to normal
operation. The Installer Configuration Menu table summarizes the configuration options. An explanation of each option
follows.
StepStep
StepStep
Step
Press button(s)Press button(s)
Press button(s)Press button(s)
Press button(s)
DisplayedDisplayed
DisplayedDisplayed
Displayed
Press Press
Press Press
Press
or or
or or
or
Comments Comments
Comments Comments
Comments
to scroll menuto scroll menu
to scroll menuto scroll menu
to scroll menu
(factory default)(factory default)
(factory default)(factory default)
(factory default)
to change optionsto change options
to change optionsto change options
to change options
1
and
LEARNLEARN
LEARNLEARN
LEARN on Select learn mode OFF or ON
(OF)
2
and
CHCH
CHCH
CH B, C, O Select sensor identification as A, B, C or O
(A)
3
and
CC
CC
C 1 through 9 Select transmitter frequency offset
(0)
4 and _____ _____ Exit installer menu and return to normal
operation
Installer Configuration MenuInstaller Configuration Menu
Installer Configuration MenuInstaller Configuration Menu
Installer Configuration Menu
1)
Select learn mode OFF or ONSelect learn mode OFF or ON
Select learn mode OFF or ONSelect learn mode OFF or ON
Select learn mode OFF or ON – Selecting
LEARN onLEARN on
LEARN onLEARN on
LEARN on
enables the sensors learning mode. In the learning mode
the sensor will transmit identification information once
every 10 seconds for a period of 10 minutes. The LEARN
icon will be displayed during the learning mode. The
transmitter icon will be displayed for a short period of time
with each transmission. See Learn Mode Option.
2)
Select sensor identification from A to OSelect sensor identification from A to O
Select sensor identification from A to OSelect sensor identification from A to O
Select sensor identification from A to O – For multiple
sensors systems, each sensor must have a designated
identification. The thermostat can operate with one indoor
sensor and one outdoor sensor. For indoor sensors you
may select A, B or C. For outdoor sensor you must select
O.
3)
Select transmitter frequency offsetSelect transmitter frequency offset
Select transmitter frequency offsetSelect transmitter frequency offset
Select transmitter frequency offset – The sensor’s
transmitter operates on 418MHz radio frequency by
default. Interference may occur if another device or
equipment operates on the same frequency. The interfer-
ence may degrade the communications between the
sensor and the thermostat. To avoid interference, you
may select a different radio frequency for your sensor.
This menu item allows you to select a radio frequency
offset from 1 to 9MHz from the base frequency. For
example; if the you selected an offset of 4, the transmitter
radio frequency will be 418MHz + 4MHz = 422MHz. Note
that the sensor’s transmitter and the thermostat’s receiver
must operate on the same frequency to communicate. To
change thermostat’s receiver frequency please refer to
Thermostat Configuration Menu.
OPERATING YOUR THERMOSTAT AND REMOTE SENSOROPERATING YOUR THERMOSTAT AND REMOTE SENSOR
OPERATING YOUR THERMOSTAT AND REMOTE SENSOROPERATING YOUR THERMOSTAT AND REMOTE SENSOR
OPERATING YOUR THERMOSTAT AND REMOTE SENSOR
NOTE
Check Thermostat OperationCheck Thermostat Operation
Check Thermostat OperationCheck Thermostat Operation
Check Thermostat Operation
To prevent static discharge problems, touch side ofTo prevent static discharge problems, touch side of
To prevent static discharge problems, touch side ofTo prevent static discharge problems, touch side of
To prevent static discharge problems, touch side of
thermostat to release static build-up before touchingthermostat to release static build-up before touching
thermostat to release static build-up before touchingthermostat to release static build-up before touching
thermostat to release static build-up before touching
any keys.any keys.
any keys.any keys.
any keys.
Do not allow the compressor to run unless the compres-Do not allow the compressor to run unless the compres-
Do not allow the compressor to run unless the compres-Do not allow the compressor to run unless the compres-
Do not allow the compressor to run unless the compres-
sor oil heaters have been operational for 6 hours andsor oil heaters have been operational for 6 hours and
sor oil heaters have been operational for 6 hours andsor oil heaters have been operational for 6 hours and
sor oil heaters have been operational for 6 hours and
the system has not been operational for at least 5the system has not been operational for at least 5
the system has not been operational for at least 5the system has not been operational for at least 5
the system has not been operational for at least 5
minutes.minutes.
minutes.minutes.
minutes.
CAUTION
!
If at any time during testing your system does not operate
properly, contact a qualified service person.
Fan OperationFan Operation
Fan OperationFan Operation
Fan Operation
If your system does not have a
G G
G G
G terminal connection, skip to
Heating SystemHeating System
Heating SystemHeating System
Heating System.
1. Turn on power to system.
2. Move FAN switch to
ON ON
ON ON
ON position. The blower should
begin to operate.
3. Move FAN switch to
AUTO AUTO
AUTO AUTO
AUTO position. The blower should
stop immediately.
Heating SystemHeating System
Heating SystemHeating System
Heating System
1. Press SYSTEM button to select
HEATHEAT
HEATHEAT
HEAT. If the auxiliary
heating system has a standing pilot, be sure to light it.
2. Press
to adjust thermostat setting to 1° above room
temperature. The heat pump system should begin to
operate. The display should show "
STG1STG1
STG1STG1
STG1". However, if the
system configuration is set to HP1 or HP2 and setpoint
temperature display is flashing, the 5 minute compressor
lockout feature is operating (see Configuration menu,
item 10).
3. Adjust temperature setting to 3° above room temperature.
If your system configuration is set at MS2, HP2 or HP1,
the auxiliary heat system should begin to operate and
the display will show "
STG 1+2STG 1+2
STG 1+2STG 1+2
STG 1+2".
4. Press
to adjust the thermostat below room tempera-
ture. The heating system should stop operating.