Filter
Top Products
I
NTREPID
9
CLEANING AND FILLING A NEW STEAM BOILER
I. BEFORE USING STEAM BOILER
A. Check burner to be certain it is ready for firing. DO NOT FIRE
into an empty boiler.
B. Be prepared to heat raw water to at least 180°F. as soon as it is
introduced into the boiler.This procedure will remove dissolved,
corrosive gases.
C. Provide drain line, with valve, from boiler. Use a bottom tapping.
L
ine and drain must be suitable for handling caustic solution.
D. Check for low water cut-off operation, see section below for
check-out.
II. CLEAN STEAM BOILER SYSTEM.
A. Fill the boiler to water line indicated on the boiler.
B. Follow start-up procedure for burner and operate the boiler with
steam in the entire system for 2 or 3 days to bring oil and dirt
from the system to the boiler.While system is in operation,
maintain the proper water level in the boiler by slowly adding
water to the boiler.
C. Shut down burner, cool down boiler and drain system.
III.
FILLING AND VENTING THE STEAM BOILER
A. Refill the boiler to the indicated water line.
B. Bring water to boiling temperature, promptly.
C. The boiler is now ready to be put into service or on standby.
BLOWING OFF A LOW PRESSURE STEAM BOILER
A. A 1-1/2" NPT tapping is provided in the front of the boiler (tapping
no. 9, figure 1) for use as a surface blow down to provide rapid
skimming of oil and grease which accumulate on the surface of the
water. The boiler should be blown down as outlined below.
B. Turn off electrical power supply to boiler. Allow boiler to cool down
and steam pressure to reduce to zero before removing skimmer
tapping plug. Check for steam pressure by testing the pop safety
v
alve. Keep your hands and all parts of your body away from the
discharge end of the saf
ety valve. Drain boiler down one to two
inches belo
w skimmer tapping.
The water might be hot. Remove
skimmer plug slowly and carefully install a 150 psi malleable iron 1-
1/2" NPT street elbow, a 1-1/2" NPT skimmer valve and length of
pipe and place a bucket underneath the open end of the pipe. Cover
bucket with a piece of cloth. (See figure 9)
C. Fill boiler slowly until water level is two inches from top of gauge
glass. (This is the starting water level for skimming only.) Fire boiler to
produce steam. If the system is heavily laden with oil, it may be diffi-
cult to obtain m
uch more than a pound or so of pressure
.
Set the
pressure control at about 7 psi.The higher the steam pressure you
can use, the better and faster the cleaning.
D. As steam develops, open the SKIMMER drain valve with caution to
skim the oil and film from the top of the water. DO NOT open the boil-
er drain valve. Close the skimmer drain valve when the water level
drops to about 5" from the top of the gauge glass
.The water may
stop before the level drops to 5" below the top of the glass. Refill boil-
er until w
ater level is again two inches from the top of the gauge
glass
.
E.
Repeat (D) above until all film is skimmed off and the water settles to
a normal movement. Add make up fresh water to the boiler as
described in (D) above, during the blow-off operation, to maintain the
proper skimming water level in the vessel. Empty bucket frequently in
order to see the difference in water cleanliness.
F. When surging has stopped and water is clean, and no film can be
seen floating in the bucket, shut off boiler, drain down to level of skim-
mer tapping, remove valve, plug skimmer tapping and refill the boiler
t
o 24-1/2" water level. After 15 minute operation, readjust level to
normal operating level of 25-1/2" from bottom of boiler (see figure 9).
Check the pop safety valve for proper operation. Check the low water
cut-off operation, see below.
G.The entire process may have to be repeated over a period of a few
days on extremely fouled systems.
LOW WATER CUT-OFF CHECK-OUT
I. Electronic probe type low water cut-off
If this boiler is factory equipped with an electronic probe type low
water cut-off, operation of cut-off should be checked at least twice a
year as follows:
A.
While boiler is running, drain down boiler water slowly through
Boiler Drain Cock shown on page 4, just until light goes on. Boiler
should shut down 10 seconds after light goes on.
B. Be sure that it is the low water cut-off and not the room thermo-
stat, pressure cut-out, or other control that has shut off the burner.
C. Refill the boiler and repeat test.
D. Refill the boiler and reset controls for normal operation.
II. Float type low water cut-off
If this boiler is factory equipped with a McDonnell & Miller float type
low water cut-off, the low water cut-off must be blown down (flushed),
at least once a week.