Filter
Top Products
–
13
–
STANDARD PROGRAMMING
C. Storing telephone numbers in memory (Sends the numeric
information to pager only)
1. Press the [MEM] key, the display will show a letter “M” on the upper left
corner. If nothing is entered within 5 seconds, the display will return to the
clock mode.
2. Within the first 5 seconds, select a memory location by pressing a keypad
number 1 - 9 to store the telephone number.
3. Enter the telephone number using the keypad. The display will flash as the
telephone is being entered. To insert a pause period between any digits
of the pre-programmed telephone number or after the telephone number
and before the numeric message. (used for pagers), a pause period must
be added between the telephone number and the numerical message. Refer
to the Pager Company to identify the pause needed (see PROGRAMMING
A PAUSE PERIOD - page 16).
6. After the telephone number has been stored, another message will appear
on the display asking for a redial count. The redial count is the number
of times the dialer will call that telephone number. The dialer is factory set
to call the number 3 times. The number of attempts can be changed to dial
1 to 9 times. If you want to keep the redial count at 3 attempts, press the
[MEM] key. To change the redial count, enter a number from 1 - 9 when
display shows "rEdIAL 3".
7. Input the repeat times when the display shows "rEPEAt 3". The repeat
time is the number of times the message will be played for that certain
phone number. The current setting is 3. It can be changed from 1 to 9 using
the keypad. Again, by pressing [MEM] will keep the existing setting.
DELETE A TELEPHONE NUMBER FROM MEMORY
1. Press [MEM] key.
2. Select the memory location (1 - 9) of the phone number you want to delete.
3. The phone number will be shown on the display, if that is the number you
want to delete, press the [R/P] key while the telephone number is on the
display. Once the phone number is deleted, the display will return to clock
mode.
4. Enter the numeric information you want to send out, ( the information that
will be shown on the pager), then press [L]. This will suspend the recorded
message.
5. Press [MEM].
–
14
–
5. The display will now show the current setting of the redial count. If you
want to keep the current redial count, enter the [MEM] key. If you want
to change the setting, enter the desired number, (1 - 9), then press the
[MEM] key.
6. After pressing the [MEM] key, the display will show the current setting
of the repeat times.
7. If you want to keep the current repeat time, enter the [MEM] key. If you
want to change the setting, enter the desired number, (1 - 9), then press
the [MEM] key.
8. The screen will revert back to clock mode.
ACTIVATE THE DIAL-ALERT WITH THE PANIC BUTTON ON THE
KEYPAD
After you programmed all the emergency telephone numbers and the voice
message, you can activate the dialer by pressing the panic button on the
keypad. Once the panic button is pressed, the dialer will start dialing the pre-
programmed emergency phone numbers. You can also activate the dialer
using the Panic Transmitter. (PT-434, sold separately).
STANDARD PROGRAMMING
1. Press the [MEM] key, display will show an “M” in the upper right corner.
2. Select the memory location of the phone number, (1 - 9)
3. The phone number will be shown on the display.
4. If you want to change the telephone number, enter the new phone number
while the old number is on the screen. This telephone number will be deleted
when a new number is added. Then press the [MEM] key. If you want to
keep the telephone number shown on the screen, press [MEM].
TO REVIEW OR MODIFY THE PRE-PROGRAMMED PHONE NUM-
BERS, THE REDIAL COUNT AND/OR THE REPEAT TIMES OF A
PHONE NUMBER.