Filter
Top Products
–
11
–
STANDARD PROGRAMMING
STORING TELEPHONE NUMBERS
This feature enables the user to program as many as 9 different telephone
numbers. The dialer can send out 2 different messages. One message is the
pre-recorded voice message that you programmed earlier, the other message
sends numeric information to a pager.
There are three different ways that you can send the voice message and the
numeric information:
A. Sends the emergency voice message only
B. Sends both the emergency voice message and the numeric infomation
(pager reception only)
C. Sends the numeric information only (for pager reception only)
Cautions:
Skylink recommends that the telephone or pager numbers of your relatives,
neighbors, office/work, friends or doctor be programmed into your Dial-Alert. Do
not program the phone number to police or fire dept directly into your Dial-Alert
unless you have checked with your local authorities. Please also inform all the
recipients that their phone numbers have been programmed into your dialer, so
they know exactly what happen when they receive your emergency message.
A. Storing telephone numbers in memory (Sends the emergency
voice message only)
1. Press the [MEM] key, the display will show a letter “M” on the upper left corner.
If nothing is entered within 5 seconds, the display will return to the clock mode.
2. Within the first 5 seconds, select a memory location by pressing a key
pad number 1 - 9 to store the telephone number.
3. Enter the telephone number using the keypad. The display will flash as the
numbers are being entered. To insert a pause period between any digits of
the pre-programmed telephone number, see PROGRAMMING A PAUSE
PERIOD (page 15).
4. Press the [MEM] key within 5 seconds after the last digit of the telephone
number is entered. The number is now stored.
5. After the telephone number has been stored, "rEdIAL 3" will appear on the
display. This is the redial count which is the number of times the dialer will
call that telephone number. The dialer is factory set to call each number 3
times. The number of attempts can be changed to dial 1 to 9 times. If you
PLAYBACK PRE-RECORDED MESSAGE
Press and release the [R/P] key, display will show “PLAY” and the dialer will
beep. The message is then played back.
If you want the dialer work without noise, means no beep or let no body knows
the dialer is dialing, just turn off the Speaker Switch inside the case.
–
12
–
STANDARD PROGRAMMING
want to keep the dialer at 3 attempts, press the [MEM] key. To change the
redial count, enter a number from 1 - 9 when display shows “rEdIAL 3” .
6. The display will now show “rEPEAt 3”. This is the repeat count which is
the number of times the message will be repeated during that one call. The
dialer is factory set to repeat the message 3 times. The number of repeats
can be changed from 1 to 9 times. If you want to keep the repeat count to
remain at 3 times, press the [MEM] key. To change the repeat count, enter
a number from 1 - 9 when display shows “rEPEAt 3” .
3. Enter the telephone number using the keypad. The display will flash as the
telephone is being entered. To insert a pause period between any digits
of the pre-programmed telephone number or after the telephone number
and before the numeric message. (used for pagers), see PROGRAMMING
A PAUSE PERIOD (page 15).
4. Press [MEM].
5. "rEdIAL 3" will appear on the display. This is the redial count which is
the number of times the dialer will call that telephone number. The dialer
is factory set to call the number 3 times. The number of attempts can
be changed to dial 1 to 9 times. If you want to keep the redial count at 3
attempts, press the [MEM] key. To change the redial count, enter a number
from 1 - 9 when display shows “rEdIAL 3”.
6. The display will now show “rEPEAt 3”. This is the repeat count which is
the number of times the message will be repeated during that one call.
The dialer is factory set to repeat the message 3 times. The number of
repeats can be changed from 1 to 9 times. If you want to keep the repeat
count to remain at 3 times, press the [MEM] key. To change the repeat
count, enter a number from 1 - 9 when display shows “rEPEAt 3”.
2. Within the first 5 seconds, select a memory location by pressing a keypad
number 1 - 9 to store the telephone number.
B. Storing telephone numbers in memory (Sends both emergency
voice message and numeric information)
1. Press the [MEM] key, the display will show a letter “M” on the upper left
corner. If nothing is entered within 5 seconds, the display will return to
the clock mode.
7. The dialer is now in standby mode. (Display shows the time).
The sequence to store a telephone number is as follows:
[MEM] , enter memory location (1-9) , enter telephone # , [MEM] , enter
redial # (1-9), enter repeat # (1-9).