Filter
Top Products
Additional instructions for starting the machine
with a power head
attached - Figures 1, 2, 3, 4, 5 & 6
Please refer to your ET or DISCO power head owner’s manual for more information.
Before turning on your canister, make sure that the vacuum handle is in its upright locked position
(figure 4). Follow steps 1-3 above.
When the power head is switched on with the handle in the upright locked position (figure 4), the brush
roller on the power head will not spin.
To release the power head from the upright locked position, press down on the foot pedal (#43, figure
5) and lower the handle into the normal operating position. Push the brush roller button on the top of
the power head (#44, figure 6) to engage the brush roller. The green light on the power head will illu-
minate.
When the canister On/Off button (#6, figure 1) is in the ON position, you may turn the power head off
and on using the power control button (#2, figure 2) on the handle. To turn the power head off using
the power control button on the handle, push the minus (-) button until the suction stops. The green
light (44) on the power head will then shut off. The blue light (8) on the canister will remain illuminat-
ed until the vacuum is powered off using the On/Off button on the canister (6).
Always turn the power off on the canister AND the power head when changing heads or
unplugging the vacuum. Press the minus (-) on the power control button (2) on the handle grip
until the suction stops, press the On/Off button (6) on the base of the canister gently with your
foot or hand, then unplug the canister to completely shut down the power when changing
heads or storing the vacuum.
Continue to page 9.
Figure 5
Figure 4
29
8
OPERATING INSTRUCTIONS
Starting the machine with a non-power-head attached
- Figures 1, 2 & 3
B
efore turning on your canister, make sure that you have a firm hold on the handle grip to keep the
machine from moving forward.
1. With the canister On/Off button (6) in the OFF position, and the power control button (2) on the han-
dle grip (1) in the OFF (-) position, grasp the plug and pull the power cord (21) out from the power
c
able recess (figure 3). The power cord (21) should be unwound from the cable reel at least two
thirds of its length. Note: do not over-extend the cord.
2. Plug the polarized power cord into a 120 volt wall outlet located near the floor.
3. Press the canister On/Off button on the base of the canister (6) gently with your foot or hand.
The blue light around the button (8) will blink right and left indicating that the power is on. Your
SEBO AIRBELT D4 has a soft-start system for longer component life. This may delay starting
slightly.
Always turn the power off on the canister AND the power head when changing heads or unplugging
the vacuum. Press the minus (-) on the power control button (2) on the handle grip until the suction
stops, press the On/Off button (6) on the base of the canister gently with your foot or hand, then unplug
the canister to completely shut down the power when changing heads or storing the vacuum.
Continue to page 9.
WARNING! The quality, condition, coating, texture, age and manufacturing
technique of all floor surfaces vary. Therefore, vacuums with rotating brushes, including your
SEBO, may damage some floor coverings or surfaces. Some types of high-gloss hardwood
floors, cushion vinyl, berber carpets, long shag, and delicate or hand-woven carpets are par-
ticularly vulnerable to damage by rotating brushes. When possible, consult the materials sup-
plied by your flooring manufacturer for information on proper upkeep and cleaning. To ensure
that your new SEBO vacuum cleaner is compatible with your floor, please test the vacuum
cleaner on each type of flooring surface in a small inconspicuous area to determine if any
damage occurs. If damage occurs, stop using the vacuum cleaner immediately!
!
Figure 1
Figure 2
0
21
Figure 3
6
8
2
1
Figure 6
44
43
7