Pella 81DU0100 Window User Manual


  Open as PDF
of 19
 
1
ROUGH OPENING PREPARATION:
A. Confirm the opening is plumb and level.
Note: It is critical the bottom is level.
*OUFSJPS
"
YOU WILL NEED TO SUPPLY: TOOLS REQUIRED:
Ř&RPSRVLWHRU,PSHUYLRXVVKLPVVSDFHUVWR
ŘJDOYDQL]HGURRILQJQDLOVOE
Ř[FRUURVLRQUHVLVWDQWZRRGVFUHZV
(Performance Upgrade & HurricaneShield)
Ř0DVRQU\VFUHZVIRUFRQFUHWHDSSOLFDWLRQV
0LQLPXPRIőGLDPHWHU[
Ř&ORVHGFHOOIRDPEDFNHUURGVHDODQWEDFNHU
WRIW
Ř3HOOD
®
SmartFlash
™
foil backed butyl window and
door flashing tape or equivalent
Ř+LJKTXDOLW\H[WHULRUJUDGHSRO\XUHWKDQHRUVLOLFRQH
VHDODQWWRWXEHVSHUGRRU
Ř*UHDW6WXII
™
Window and Door Insulating Foam
Sealant by the Dow Chemical Company or equiva-
lent low pressure polyurethane window and door
IRDP'2127XVHKLJKSUHVVXUHRUODWH[IRDPV
Ř6LOOSDQRSWLRQDO
Ř3HOODDOXPLQXPVLOOVXSSRUWRUZRRGEORFNLQJ
Ř,QWHULRUWULPDQGRUMDPEH[WHQVLRQVWRIW
Installation Clip Option:
ŘRULQVWDOODWLRQFOLSV
Ř[FRUURVLRQUHVLVWDQWIODWKHDGZRRGVFUHZV
Ř[FRUURVLRQUHVLVWDQWVFUHZVRU[
PDVRQU\VFUHZV
Ř7DSHPHDVXUH
Ř/HYHO
Ř6TXDUH
Ř+DPPHU
Ř6WDSOHU
Ř6HDODQW*XQ
Ř6FLVVRUVRUXWLOLW\NQLIH
Ř7LQ6QLSV
Ř6FUHZGULYHUV
3KLOOLSVZLWKVKDIW
and small flat blade)
Ř77RU[:UHQFK
(Architect Series
®
)
Ř$OOHQZUHQFK
(Designer Series
®
)
Ř'ULOO
Ř'ULOO%LWVDQG
DQGPDVRQU\ELWIRU
concrete applications
4&"-"/5
4&"-"/5
The performance of any building is dependent upon the design, installation, and workmanship
RIWKHHQWLUHEXLOGLQJV\VWHP3HOOD&RUSRUDWLRQVWURQJO\UHFRPPHQGVFRQVXOWLQJDQH[SHULHQFHG
architect, contractor or structural engineer prior to installation of Pella products.
The individual (building owner, architect, contractor, installer and/or consumer) responsible for the
project must take into account local conditions, building codes, inherent component limitations,
the effects of aging and weathering on building components, and other design issues relevant to
each project.
The determination of the suitability of all building components for each project, as well as the
design and installation of flashing and sealing systems, are the responsibility of the building owner,
architect, contractor, installer and/or consumer.
 previous next