Filter
Top Products
USER
CHECK LIST
This appliance was inspected thoroughly and was in good operating condition
when it was shipped from the factory. If a minor problem develops, it usually
can be remedied quite easily when the cause is identified. Accordingly, this
check list is provided for your convenience.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
..~........~.......................................................................
Problem Possible cause
Possible solution
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...*..............
Clean
1. Not firmly plugged in.
1.
Plug unit in firmly.
won’t
2. No voltage in wall plug.
2. Check fuse or breaker.
run
3. Blown fuse/tripped breaker.
3. Replace fuse/reset breaker.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
..*.......*......*............................*..............................................................
Cleaner
1. Broken or worn agitator belt. 1. Replace belt.
won’t
2. Agitator brushes worn.
2. Replace brushes.
pick up
3. Bag full.
3. Change throw away bag.
4.
Hose(s)/valve
clogged.
4. Clear hose and/or valve.
5. Secondary filter clogged.
5. Clean filter.
6. Bag not opening.
6. Open bag by pulling pleats.
7. Suction dial improperly set.
7. Check to be sure dial is set
properly.
. . . . . . . . . . .
..~~~.......~..~~.~~~~.....~.~.....~~.~~~~.....~...............~~~..~~~~.~........~~.~~~.~..~..............~.......~...~.~..~~.
Cleaner
1. ‘Power ‘Drive’ belt broken or 1. Replace belt.
won’t
worn.
drive
2. Manual transport button
2. Make sure handle grip slides
pushed down.
freely.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
..*....*...........................*....................................................................
If the problem persists, check the telephone book for a HOOVER COMPANY
listing, or consult the white insert accompanying this manual for the nearest
location where approved service and genuine HOOVER replacement parts may
be obtained. For service under warranty, follow the instructions in the warranty
provided with this product.
Always identify your cleaner by model number when requesting information
or ordering replacement parts. (The model number appears on the belt guard on
the bottom of the cleaner.)
If further assistance is needed, contact the Hoover Company Customer Rela-
tions Department, North Canton, Ohio
44720,216-499-9200.
Lubrication The motor is equipped with one ball bearing and one sleeve bearing.
These bearings contain sufficient lubrication for the life of the motor. The addi-
tion of lubricant could cause damage. Therefore, do not add lubricant to either
motor bearing.
The agitator is equipped with two ball bearings that should be lubricated peri-
odically, This should be done by the Hoover Factory Branch Service Center, or
the Authorized Hoover Warranty Service Dealer, as listed on the white insert,
14