Filter
Top Products
T7200D,E, T7300D,E,F AND Q7300 SERIES 2000 PROGRAMMABLE COMMERCIAL THERMOSTATS AND SUBBASES
63-4355—416
Setting Keypad Lockout Switch (T7300
only
)
The DIP switch 1, on the thermostat back, activates the
lockout features. The switch must be set
ON
(up) to activate
the lockout feature (see Fig. 17).
NOTE: The factory setting is
off
(down).
If keypad lockout is desired:
1.
Remove the thermostat from the subbase.
2.
Set the switch to
ON
.
3.
Enter the Installer Setup.
4.
Select option 25 to choose the level of keypad lockout
(see Table 7).
5.
Activate the lockout by setting option 40 to
1
.
Fig. 17. Set keypad lockout DIP switch 1.
PROGRAMMING
The thermostat operates at the Unoccupied temperature
setting unless the thermostat is programmed. Table 10 shows
the default temperature settings. (The program has four):
— Occupied heat.
— Occupied cool.
— Unoccupied heat.
— Unoccupied cool.
Table 10. Occupied and Unoccupied
Default Temperature Settings.
The keyboard is located behind the thermostat cover. Up to
sixteen keys are used to set, review and modify programmed
times and temperature settings. The thermostat display shows
day, time, program period and temperature.
The thermostat can be set for two Occupied and two
Unoccupied times for each day of the week (28 independent
time settings). Temporary Occupied key provides quick
temporary temperature changes for increased occupant
comfort. The Continuous Unoccupied key provides energy
efficient operation for extended periods of time.
IMPORTANT
To program the thermostat, 24 Vac is required (turn
on system power). The keyboard lockout feature
must be disabled by setting the DIP switch 1 on the
back of the thermostat to the Off position.
NOTE: Before starting the program procedure, use Table 11
to organize the program schedule.
Table 11. Occupied and Unoccupied Periods Start Times.
Setting Current Day/Time
1.
Press
Set Current Day/Time
.
NOTE: On initial power up or after an extended power
loss, the display flashes
1:00 pm
until a key
is pressed.
2.
Press
Day
until the current day is displayed.
NOTE: Sun = Sunday, Mon = Monday, Tue = Tuesday,
Wed = Wednesday, Thu = Thursday,
Fri = Friday, Sat = Saturday.
3.
Press increase
▲
or decrease
▼
until the current time
is displayed.
NOTE: Tapping
Set Current Day/Time
changes the
time in one hour increments.
4.
Press
Run Program
.
Control Occupied Unoccupied
Heating 70°F (21°C) 55°F (13°C)
Cooling 78°F (26°C) 90°F (32°C)
ON
1
2
M10235BACK OF THERMOSTAT
1
2
1
2
DIP 1 IS ON
DIP 2 IS NOT USED.
Day
Occupied
Period 1
Unoccupied
Period 1
Occupied
Period 2
Unoccupied
Period 2
Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
Sunday
M4951B
Set Current
Day/Time
Set Program Set Temperature Change
Time/Temp
Occupied
Temp
Unoccupied
Start Time Day
System Fan
Copy
Occupied
Start Time
Run
Program
Temporary
Occupied
Continous
Unoccupied
Set Current
Day/Time
Clear
Start Time
Unoccupied
Temp
Heat/Cool
Settings
Mon
PM
Set Day/Time
M4952B
Set Program Set Temperature Change
Time/Temp
Occupied
Temp
Unoccupied
Start Time Day
System Fan
Copy
Occupied
Start Time
Run
Program
Temporary
Occupied
Continous
Unoccupied
Set Current
Day/Time
Clear
Start Time
Unoccupied
Temp
Heat/Cool
Settings
Day
PM
Tue
Set Day/Time
M4953B
Set Program Set Temperature Change
Time/Temp
Occupied
Temp
Unoccupied
Start Time Day
System Fan
Copy
Occupied
Start Time
Run
Program
Temporary
Occupied
Continous
Unoccupied
Set Current
Day/Time
Clear
Start Time
Unoccupied
Temp
Heat/Cool
Settings
PM
Tue
Set Day/Time
M4954A
Set Program Set Temperature Change
Time/Temp
Occupied
Temp
Unoccupied
Start Time Day
System Fan
Copy
Occupied
Start Time
Run
Program
Temporary
Occupied
Continous
Unoccupied
Set Current
Day/Time
Clear
Start Time
Unoccupied
Temp
Heat/Cool
Settings
Auto
System Fan
Mon
Room
AM
Occupied 1
Heat
Run
Program