Filter
Top Products
SETTING CONTACT
REVERSEFUNCTION
NOTE
Limit Switchand ForceAdjustments must be completed before
checkingthe contact reversefunction.
A Open garage door using Wall Console.
B Lay a 2" x 4" board flat in center of doorway (Figure 10).
C Close door using Wall Console.
D Check that door stops and reverses within 2 seconds after it
contacts board:
• If door does not reverse, decrease Close Force until
door reverses (Figure 9).
• If door still does not reverse, move Limit Switch
toward door.
E Check Safe-T-Beam ®System operation:
• If beam is blocked, door
will not close.
Figure 10 F
Checking _J
2" x 4" board
Contact
/J_-_ laid flat
Reverse
NOTE
The door must contact the 2" x 4" board before the
Carriage activates the Close Limit Switch. If not,
readjust the Close Limit Switch.
ACCESSORIES
PROGRAMMING THE
REMOTE CONTROL
A To program one Button of a Remote Control (Figure 11):
• Locate Learn Button and Learn Indicator Light near
Terminal Block on Power Head (Figure 12).
• Press and release Learn Button. Red Learn Indicator Light
will blink 2times per second.
• Press Remote Control Button once within 30 seconds. Red
Learn Indicator Light will stay lit.
• Press Remote Control Button again. Red Learn Indicator
Light will go out, indicating that memory isstored.
• Press again to Activate Unit.
B Program each additional Remote using step A above.
To Erase All Remotes from Power Head Memory
A Press and hold Learn Button on Power Head for 10 seconds
or until Learn Indicator Light goes out. Memory is erased:
• Program Remotes again as needed.
To Replace Remote Control Battery
A FOR NON-FLASHLIGHTMODELS
• Pop off the back of the transmitter.
- Use coin, pen, screwdriver or any similar device.
- Replace old Battery with new coin type battery.
o Replace back of remote.
B FOR FLASHLIGHT MODELS
• Slide open battery cover.
- Replace old Battery with new AAA battery.
o Replace battery cover.
A WARNING
Amoving garagedoor maycauseserious njuryor death.
--_ Keeppeopleclearof openingwhile door is moving.
Donot allow childrento play with the RemoteControls,
Ifthe SafetyReversedoesnot work properly:
" Closethedoor anddisconnecttheOpenerusingthe
EmergencyReleaseCord.
, Donot usethedoor Opener,RemoteControls,or
WirelessKeypad.
• Referto thedoor anddoor 0 penerOwner'sManuals
beforeattempting any repairs.
Remote Control Operation
A
B
Figure 1 1
1-Button and 3-Button
Compact Remotes
w/Docking Station
PressButton on Remote Control. Garage door will move.
Press Button again. Garage door will stop:
• The door automatically stops at the end of the
open or close cycle.
Press Button again. Garage door will reverse.
D There are several additional varieties of remote controls
available from your local dealer, some equipped with
a flashlight.
LOCATED
UNDERTHE
LIGHT COVER
_b
©
....@(h
CLOSE@ MOREFORCE
©
LEARN
INDICATOR
_-- LIGHT
---- LEARN
CODE
BUTTON
Figure 12 Learn Code Button and Indicator Light.
(Located Lower Right Corner).
NOTE
e
Each Remote Control must be programmed
separately.
• The Remote Controls will not close the garage with
malfunctioning Safe-T-Beam®System.
• Program Remote Controls, while at least 24" from
Antenna Wire.
• If the red Learn Indicator Light blinks rapidly,
programming stopped. Restart programming.
• Each Button on a multi-button Remote Control is
for a different Opener. Cannot use more than one
Button for same Opener.
• A maximum of seven Remote Controls or Wireless
Keypads can be stored into the Receiver at one
time. If a Remote Control becomes lost, or if you
want to delete a Remote Control or Wireless
Keypad, see "To EraseAll Receiver Memory."
8 For Help, call 1-800-3S-GENIE or visit www.geniecompany.com