Filter
Top Products
Simon Security System
14
Figure 1. Opening the panel cover
Programming Instructions
Use the following instructions to access the programming buttons and programming
decals.
Note
If Trouble Beeps are turned
on, the panel will sound six
trouble beeps every minute
the panel cover is open. Ask
your installer if Trouble
Beeps are turned on for your
system.
1. System must be disarmed. Open the Panel Cover by pressing the plastic latch on
the top of the panel. When you open the cover you will immediately be prompted
by the panel voice to use the numbered keys to enter your ID.
Note
The Master access code is
1-2-3-4 when the panel is
shipped. You should change
your Master Access Code
after your system is installed
(see “Access Code”).
2. Enter the Master Access Code.
3. The system voice will prompt you to begin with the START MENU.
The START MENU includes the following buttons:
•Add
• Delete
• Cancel
Test Weekly
C O D E
Status
System
9 / 0
Windows
Doors &
Sensors
Motion
Disarm
5 / 6
Arm
3 / 4 7 / 8
On
Off
AUX
SensorMotion Time
FIRE
POLICE
Lights
Special
H O M E C O N T R O L
E M E R G E N C Y
H O M E S E C U R I T Y
Doors
Chime
32
978
10
645
Test
System should be checked
422-2806 Rev A
Set
Code
Access Clock
+
Delete
Delete
press
-
+
Hours
at least every three years.
To delete an option or access code
Hold key or press
and follow the voice
repeatedly until you
hear the desired item.
Note:
Cancel
and
Test
Cancel
DONE
Minutes
, then
DONE
See Note
If you make a mistake or want to
Sensor or Phone Test
follow the voice prompting.
To select a test, press
start over press
prompting.
by a qualified technician
Delete
START MENU
Add
Version 3
MAIN MENU
*
Remote
Sensor/
**
Control
Light
Option #
**
Sensors
-
*
Entry/Exit
Delay
CONTROL MENU
*
Press for program
information.
Instruction
Add Option
Summary
Unit #
Add
Press
Clock Set
Press
Set Clock
DONE
Chime Voice
Latchkey Time
Panel Voice
AddOption #
Press
Option #42:
Option #43:
Option #55:
Option #41:
Option #2:
Option #3:
Option #36:
Option #37:
See Note
Sensor Activated Light Lockout Start Time
Sensor Activated Light Lockout Stop Time
and follow voice prompts.
Pager Phone Number
Speaker Volume
Status Beep Volume
Option #1:
Panel Beeps
use red numbers to enter 4-digit code.
Add Access Code
Hours
Access Code
See Note
Minutes
Time
Cancel
1 / 2
1.
Press Down
2.
Open
Cove
r
32
978
10
645
Test
System should be checked
422-2806 Rev A
Set
Code
Access Clock
+
Delete
Delete
press
-
+
Hours
at least every three years.
To delete an option or access code
Hold key or press
and follow the voice
repeatedly until you
hear the desired item.
Note:
Cancel
and
Test
Cancel
DONE
Minutes
, then
DONE
See Note
If you make a mistake or want to
Sensor or Phone Test
follow the voice prompting.
To select a test, press
start over press
prompting.
by a qualified technician
Delete
START MENU
Add
Version 3
MAIN MENU
*
Remote
Sensor/
**
Control
Light
Option #
**
Sensors
-
*
Entry/Exit
Delay
CONTROL MENU
*
Press for program
information.
Instruction
Add Option
Summary
Unit #
Add
Press
Clock Set
Press
Set Clock
DONE
Chime Voice
Latchkey Time
Panel Voice
Add Option #
Press
Option #42:
Option #43:
Option #55:
Option #41:
Option #2:
Option #3:
Option #36:
Option #37:
See Note
Sensor Activated Light Lockout Start Time
Sensor Activated Light Lockout Stop Time
and follow voice prompts.
Pager Phone Number
Speaker Volume
Status Beep Volume
Option #1:
Panel Beeps
use red numbers to enter 4-digit code.
Add Access Code
Hours
Access Code