Filter
Top Products
5
OPERATING INSTRUCTIONS
3.12 We would recommend that the stove be burnt at high
output for at least 30 minutes each day when it is in use.
This will help reduce the build-up of tars and creosotes
within the stove and flue system.
Do not burn painted, impregnated wood or
manufactured board products.
4.1 Open the
Airwash control to approximately 50% and
Primary air control fully.
4.2 Place some pieces of firelighter or dry crumpled paper on
the grate and cover with some small pieces of dry kindling
wood. Light the paper or firelighters.
4.3 To avoid the build-up of condensation on the door glass
it is advisable to leave the door slightly open as the fire
establishes, and the glass warms.
4.4 As the fire becomes established add pieces of solid fuel
and fully close the door. Do not leave the stove with the
door open as this could over-fire the stove and cause
permanent damage.
4.5 As the fire becomes established reduce the Airwash control
to approximately 25% and control the burn rate using the
Primary air control only.
4.6 To burn solid fuel efficiently it is best to control the
combustion using the Primary air control only.
4.7 Before re-fuelling the stove it is advisable to first de-ash the
firebed, using the riddling grate system. To do this open
the stove door, then using the ashpan tool move the grate
vigorously left to right. This causes the ash to fall down into
the ashpan. Do not use bare hands to operate the riddling
system.
4.8 Then open the
Primary air control fully for a few minutes,
to establish a glowing bed before adding new fuel. Allow
the new fuel to burn at high output for a few minutes
before adjusting the burn rate with the Primary air control
to the desired setting. It is best to refuel little and often to
maintain clean and efficient burning.
4.9 The ideal control settings to suit the particular installation
and personal preferences will be established by experience
in using the stove.
4.10 Do not load fuel higher than the log guard at the front of
the stove and the secondary combustion air inlet holes at
the back of the fire box.
4.11 We would recommend that the stove be burnt at high
output for at least 30 minutes each day when it is in use.
This will help reduce the build-up of tars and creosotes
within the stove and flue system.
Do not burn bituminous coal, ‘petro-coke’ or other
petroleum based fuels, as this will invalidate any product
guarantee.
5.1 Do not use the appliance at maximum output for prolonged
periods of time, or over fill the firebox with fuel, as this
could result in over-firing. If the connecting fluepipe,
appliance flue collar or top plate glow red with heat the
appliance is being over fired and the air controls should be
closed to reduce the output.
5.2 If a chimney fire occurs shut all air controls immediately to
close the appliance down, and evacuate all persons from
the building before calling the fire brigade. Do not re-enter
the building until it is confirmed safe to do so.
5.3 Following a chimney fire do not use the appliance until it
is inspected by a HETAS (GB only)/ INFO (Eire) registered
installer, to confirm that the appliance is safe to use, or
make any repairs required before re-use. Only genuine
Stovax replacement parts are to be used to keep your
appliance in safe and efficient working order.
5.4
After any chimney fire it is recommended that the chimney
system be inspected and swept by a NACS registered (UK
only) chimney sweep, to confirm that the system is structurally
sound and free from any obstructions before re-use.
6.1 If the stove is not to be used during the warmer periods of
the year it is recommended to clean and service the stove,
as detailed in the Maintenance and Servicing section.
6.2 The air controls should be set in the 50% open position to
keep the appliance ventilated, and stop the build-up of any
moisture inside.
6.3 Before re-lighting the stove remove the baffles, clear any
debris that may have accumulated, and check the flue is
clear of any blockages.
7.1 The burning of any fuel will produce ash, which will have
to be removed after a period of use. This time will depend
on the fuel used. Before removing the ash from the stove it
is advisable to let the fire burn down to a low level, or even
go out completely. If a multifuel kit is fitted the ashpan can
be removed from the stove using the tool provided, after
opening the door.
7.2 As heat can remain in the ash for a long period after use,
care must be taken when removing and carrying the full
ashpan. We suggest that the ashpan be carried using gloved
hands, or the ash is placed directly into a Stovax Ash Caddy.
(Stovax Part No. 4227).
7.3 When burning wood the amount of ash will be smaller and
may only need removal once every week. To do this, allow
the fire to burn out and cool. Then after removing the log
4. BURNING SOLID FUEL
(with multifuel kit fitted)
5. OVER-FIRING
6. SEASONAL USE
7. ASH REMOVAL