Filter
Top Products
Page 3
Auth. Required
Enter Valid Pin
01-Bus Module
Enrollment
Enrolling the M1KPAS Arming Station: (This step requires an LCD Keypad or the ElkRP software)
1. Press the ELK key, then press 9 (or scroll up) to display 9 - Installation Programming. Press the RIGHT
arrow key to select this menu. The Installer Program Code (PIN) must be entered to access this menu.
2. Enter the Installer Program Code. (See M1 Manual for the default Code)
3. The first Installer Programming menu displayed will be "Bus Module Enrollment"
4. Press the RIGHT arrow key to select this menu. "Enrolling Bus Modules" will display
5. The M1 will transmit an enrollment message to all data bus devices, following by a display showing the total
Bus Modules that are enrolled. To view the enrolled devices and/or remove a device press the RIGHT arrow
key to select Edit mode.
6. Press the * or Exit keys to exit Installer Programming.
XX Bus Modules
Enrolled, Editr
Keypad
Address
Exit (Blue)
= 16
When the M1KAS is in setup mode the LEDs will display the
address setting in Binary Representation
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Stay (Blue)
= 8
Ready
(Red) = 4
Trouble
(Yellow) = 2
Armed
(Red) = 1
On - - - -
-On-- -
On On - - -
--On- -
On - On - -
-OnOn- -
On On On - -
---On -
On - - On -
-On-On -
On On - On -
--OnOn -
On - On On -
-OnOnOn -
On On On On -
---- On
Address and Enrollment
Keypads and expander devices that operate on the RS-485 4-wire data bus must each have a unique address setting from 1 to 16
within their device TYPE. Keypads are device TYPE 1, input (zone) expanders are TYPE 2, output expanders are TYPE 3, etc. The
purpose of device types is so that the address numbers can be re-used in each different device type. It is OK to have a Keypad, a Zone
Expander, and a Output Expander all set to address 2 on the same data bus since each device is a different device type. It is NOT OK
to have duplications of addresses within the same device type. I.E. Multiple keypads on a control cannot be set to 'like' addresses.
The M1KPAS is factory preset to address 16. Valid addresses are 1 to 16. Whenever an M1 control is powered up for the first time only
the first keypad (address 1) is automatically enrolled. Any
additional keypads must be manually enrolled from “Menu 1 - Bus Module
Enrollment”. Before enrolling each device will need to be set with an address.
Setting the Address of an M1KPAS Arming Station:
1. Press and hold the " * " key for 10 seconds. This will place the M1KPAS arming station into setup (bootloader) mode which
is indicated by the numeric keys blinking On and Off together. NOTE: Another way to access the setup mode is to remove
power by unplugging the data bus cable and applying power while holding any key pressed.
2. Once the unit is in setup mode press the "F" key followed immediately by the "1" key. The unit will now display its current
address setting utilizing the Ready (Green), Trouble (Yellow), Armed (Red) LEDs and the EXIT and STAY keys. Each LED
or key has an assigned binary value. See table below. The EXIT key (value of 16) will be lighted by itself when the M1KPAS
is fresh from the factory.
3. Enter the desired new address number from 1 to 16 and press the EXIT key. OR Press the EXIT key by itself to exit without
changing the address.
4. To exit completely from the setup mode press the EXIT key again. The numeric keys will stop blinking On and OFF.
5. The Ready, Trouble, Armed, Exit, and Stay keys will all begin lighting in a clockwise process to indicate that the keypad has
not been enrolled with the control. Proceed to the ENROLLING process to make the keypad operational.
ELK-M1KPAS
EXAMPLE
Address 3
would be
indicated by
these 2 LEDs
being ON
Ready Trouble Armed