Filter
Top Products
Radio Controls
EC.C. rules prohibit adjustments to or modification of receiver and transmitter circuitry except for changing the
code setting and replacing the transmitter battery THERE ARE NQ OTHER USER SERVICEABLE PARTS
Manufactured under ! or more of the fol_owlng U.S. patents: RE2g_525; 4,03"7,201; 4,750,1t8; 4,806,930
Your 53000SR SERIES garage door opener (with RECEIVER 'SR' CODE BUTTON) has been factory set to operate
with the LARGE push button on the transmitter, The 3-function transmitter(s) can also activate additional garage
door openers and/or light controls. 53000 and/or 53000SR SERIES.
Instructions are given below for matching the code in all transmitters, changing your code selection or using the
transmitter(s) with other receivers,
MATCH/CHANGE THE CODE IN TRANSMITTER(S)
SET CODE SWITCHES IN ALL TRANSMITTERS TO MATCHING POSITIONS
1. Locate the code switches in transmitter(s), either by sliding batteq/compartment cover down or by removing cover
screw and carefully turning case top overr
2. With a pen or a screwdriver, change the setting of one or more switch (to a (+), (-) or (0) position).
NOTE: Code switches 2 through g in ALL transmitters used to operate e receiver must be set to match. (Code
switch 1 on a 34unction transmitter is neutral Set it to ANY position° It will not affect the code selected).
'--- 3 Standard
3*Function
] t _"_ .... _-_---.Code Switches
__!i Standard
"--- 3_Function
Trat_s miller
"*-COde Switches
,, (2.9)
SET RECEIVER TO MATCH TRANSMITTER(S) CODE
53000SR SERIES (WITH RECEIVER CODE BUTTON)
Garage Door Openers and Light Controls
(illustration A shows a garage door opener receiver)
3 FUNCTION A GARAGE DOOR
TRANSMITTER _ OPENER RECEIVER
(Wilh SR Code Button)
Select a trar_smi[ter push AE_ v_rr e,_K 'tEL
burton to operate receiver
%%% %
SR tnd[caler
Code Button Light
3. Press the RECEIVER SR code button on the right side
panel of opener (Illustration A) The indicator light will
turn ON.
4, STAND AWAY FROM THE DOOR and press the
selected push button on the transmitler The indicator
light will turn OFF and door will move, Receiver and
transmitter codes now match and the opener will
operate with the selected push button on the transmitter,
NOTE: tf transmitter push button is not pressed
within 30 seconds, the indicator light wilt turn OFF.
Begin again at Step 3.
TO USE THE TRANSMITTER(S) WITH OTHER 53000SR
SERIES RECEIVERS: Select another transmitter push
button to operate the Light Control or additional garage
door opener, Make sure all transmitters used to operate
receiver are set to the same code (Steps 1 and 2) Repeat
Steps 3 and 4,
3-Function
Mini Transmitter
Code Switches
0-9}
53000 SERIES (WITH RECEIVER CODE SWITCHES)
Garage Door Openers and Light Controls
(Illustration B shows a garage door opener receiver)
Push Button (-}
Push Bu_
Push Button (el
%
\
Code Switch #t ('l
Receiver wiiI operale
with _ransmitters'
large push butlon
B 3 FUNCTION
TRANSMITTER
Select atransmitter
push butlon to operate
receiver
YEL GARAGE DOOR
OPENER RECEIVER
(With Code Switches)
S{ide receiver code
switch #1 to posit.ion
that matches r_e_ected
transmitter push buItoo
(+; 0 or -)
3 Locate the receiver code switches Set code switch #1
to match transmitter push button you want to use with
that receiver (+), (0) or (-). Refer to illustration (B).
4. Hold a transmitter (with code switches visible) along-
side the receiver. Beginning with RECEIVER code
switch #2, match the position of each transmitter
switch,
TO USE THE TRANSMITTER(S) WITH OTHER 53000
SERIES RECEIVERS: Select another transmitter push
button to operate the Light Control or additional garage
door opener. Make sure all transmitters are set to a match-
ing code (Steps I and 2), Repeat Steps 3 and 4
' ,,,,,,u i i , ,,,,, ,i,,t ,, ii
19