Craftsman 139.53660SRT1 Garage Door Opener User Manual


 
i,
Installation Step 6
Install the Door Control
Locate the door control within sight of the door
at a minimum height of 5 feet where small
children cannot reach, and away from all moving
parts of the door and door hardware.
The door control is typically attached directly to the
wall. If installing into drywall, drill 5/32" holes and
use the anchors provided. For pre-wirad installations
'as in new home construction.), Console models
may be mounted to a standard single gang box
"Figure 2).
1. Strip 1/4" of insulation from one end of the bell
wire and connect it to the two screw terminals on
the back of the door control: white to 2 and
white/red to 1.
2. Door Control Button: Fasten securely with
6ABx1-1/2" screws.
Console Model: Pry off cover along one side
with a screwdriver blade (Figure 1). Fasten with
6ABx1-1/4" self-tapping screws (standard
installation) or 6-32x1" machine screws (pre-wired
installation) as follows:
Install bottom screw, allowing 1/8" to protrude
above wall surface.
Position bottom of door control on screw head
and slide down to secure. Adjust screw for snug
fit.
Install top screw with care to avoid cracking
plastic housing. Do not overtighten.
Insert top tabs and snap on cover.
3. (For standard installation only) Run the bell wire
up the wall and across the ceiling to the opener.
Use insulated staples to secure the wire in
several places. Be careful not to pierce the wire
with a staple, creating a short.
4. Connect the bell wire to the terminal screws on
the opener panel: white to 2; white/red to 1.
5. Position the antenna wire as shown.
Lighted Lighted
P°shBotto :,
DOOR
CONTROL STANDARD
BuTroN CONTROL
CONSOLE
PREMIUM
CONTROL
CONSOLE
Lighl
Lock
Back Panel
of Opener
Do not connect to live electrical wiring. Connect
only to 24 Volt low voltage wires. Connection to
live wires or higher voltage may cause setfous
injury from shock, burn or electrocution.
Children operating or playing with a garage
door opener can injure themselves or others.
The garage door could close and cause
serious injury or death.
Install the door control (or any additional push
buttons) out of the reach of children and away
from all moving parts of the door and door
hardware, but where the garage door is visible.
Do not allow children to operate the push
button(s) or the remote control(s).
A moving garage door could injure someone
under it. Activate the opener only when the
door is properly adjusted, you can see it clearly,
and there are no obstructions to door travel.
_..IIlllllllll_lllltllllll=l IIIt'll>
6AB x 1-1/2" Screw
Door Control Button
_ Illllllllltllll_llllllll]>
6AB x 1-1/4" Screw Insulated
Control Console (std installation) Staples
Control Console (pre-wired) Dry Wall Anchors
Hardware Shown
Actual Size
Figure 1 Figure 2
PRE-WIRED
REMOVE & REPLACE COVER INSTALLATION
ToReplace,TopFirstinsertTabs _ _ _ ,* ToRemove, //_TwistHere "*
__ 2-Conductor
Bell Wire
Antenna
18
DOOR CONTROL
BuTroN (BACK)
Terminal Screws
STANDARD CONTROL
(BACK VIEW
Top
_Mounting
Hole
Terminal
" Screws
Bottom
Bell _. Mounting
Wire Hole
PREMIUM CONTROL
(BACK VIEW)
_ Top
Mountin_
,v, - Hole
_'_=TE_" Terminal
...... Bottom
,1 =._:_ Mountin,
-- Hole