Titan Tool ED655 Manual

Open as PDF

next previous

Important Safety Information · Read all safety information before

operating the equipment. SAVE THESE INSTRUCTIONS.

8. Check hoses and parts for signs of damage, a leak can

inject material into the skin. Inspect hose before each use.

Replace any damaged hoses or parts.

9. This system is capable of producing 2750 PSI / 190

Bar. Only use replacement parts or accessories that

are specied by the manufacturer and that are rated a

minimum of 2750 PSI. This includes spray tips, nozzle

guards, guns, extensions, ttings, and hose.

10. Always engage the trigger lock when not spraying. Verify

the trigger lock is functioning properly.

11. Verify that all connections are secure before operating the

unit.

12. Know how to stop the unit and bleed pressure quickly. Be

thoroughly familiar with the controls. Pressure will not be

released by turning off the motor. The PRIME/SPRAY

valve or pressure bleed valve must be turned to their

appropriate positions to relieve system pressure. Refer

to PRESSURE RELIEF PROCEDURE described in the

pump manual.

13. Always remove the spray tip before ushing or cleaning

the system.

NOTE TO PHYSICIAN:

Injection into the skin is a traumatic injury. It is important

to treat the injury as soon as possible. DO NOT delay

treatmenttoresearchtoxicity.Toxicityisaconcernwith

some coatings injected directly into the blood stream.

Consultation with a plastic surgeon or reconstructive

hand surgeon may be advisable.

d) WARNING - To reduce the risk of injury:

1. Always wear appropriate gloves, eye protection, clothing

and a respirator or mask when painting. Hazardous

vapors – Paints, solvents, insecticides, and other materials

can be harmful if inhaled or come in contact with body.

Vapors can cause severe nausea, fainting or poisoning.

2. Do not operate or spray near children. Keep children

away from equipment at all times.

3. Do not overreach or stand on an unstable support. Keep

effective footing and balance at all times.

4. Stay alert and watch what you are doing.

5. Do not operate the unit when fatigued or under the

inuence of drugs or alcohol.

6. Do not kink or over-bend the hose. Airless hose can

develop leaks from wear, kinking and abuse. A leak can

inject material into the skin.

7. Do not expose the hose to temperatures or pressures in

excess of those specied by manufacturer.

8. Do not use the hose as a strength member to pull or lift the

equipment.

9. Use lowest possible pressure to ush equipment.

10. Follow all appropriate local, state and national codes

governing ventilation, re prevention and operation.

11. The United States Government Safety Standards have

been adopted under the Occupational Safety and Health

Act (OSHA). These standards, particularly part 1910 of

the General Standards and part 1926 of the Construction

Standards should be consulted.

12. Before each use, check all hoses for cuts, leaks, abrasion

or bulging of cover. Check for damage or movement

of couplings. Immediately replace hose if any of those

conditions exist. Never repair a paint hose. Replace with

a conductive high-pressure hose.

13. Do not spray outdoors on windy days.

14. Always unplug cord from outlet before working on

equipment (electric models only).

Important Electrical Information

IMPORTANT: Useonlya3-wireextensioncordthathas

a 3-blade grounding plug and a 3-slot receptacle that will

accepttheplugontheproduct.Makesureyourextension

cordisingoodcondition.Whenusinganextensioncord,

be sure to use one heavy enough to carry the current your

product will draw. An undersized cord will cause a drop

in line voltage resulting in loss of power and overheating.

A 14 or 12 gauge cord is recommended (see chart). If an

extensioncordistobeusedoutdoors,itmustbemarked

withthesuffixW-Aafterthecordtypedesignation.For

example,adesignationofSJTW-Awouldindicatethatthe

cord would be appropriate for outdoor use.

Cord gauge Maximum cord length

12 150 feet

14 100 feet

IMPORTANT: This unit is provided with a thermally

protected automatic reset. If an overload occurs the

thermally protected automatic reset disconnects the motor

from the power supply.

• The motor will restart without warning when the protector

automatically resets.

• Always disconnect the motor from the power supply before

working on the equipment.

• When the thermally protected automatic reset disconnects

the motor from the power supply, relieve pressure by

turning the priming valve to PRIME.

• Turn the ON/OFF switch to OFF.

NOTE: The cause of the overload should be corrected

before restarting. See Troubleshooting.

Specications

Weight ...................................... 27 lbs

Capacity.................................... Up to .35 gallon (1.25 liters) per

minute

Power source............................ Electric motor, totally enclosed,

fan cooled

Power requirement ................... 15 amp minimum circuit on 115

VAC, 60 Hz current.

Generator ................................. 15 amp A/C.

Spraying pressure .................... Up to 2750 PSI

Capabilities ............................... Sprays a variety of oil-based and

latex paints, primers, and stains