Hunter Fan 41844-01 Manual

Open as PDF

next previous

3. Align the keyhole slots in the upper switch housing with the

housing assembly screws installed previously.

4. Turn the upper switch housing counterclockwise until the

housing assembly screws are firmly situated in the narrow end

of the keyhole slots as shown in Figure 23. Install the one re-

maining #6-32 x 3/8" housing assembly screw into the third

hole in the upper switch housing. Tighten all three screws firmly.

urur

e 23 - Me 23 - M

e 23 - M

unun

inin

g tg t

g t

e upe up

e up

r sr s

r s

h hh h

h h

sinsin

sin

N: MN: M

N: M

e se s

e s

urur

e te t

e t

e upe up

e up

r sr s

r s

h hh h

h h

sinsin

sin

g ig i

g i

s ss s

s s

e-e-

urur

y ay a

y a

d td t

d t

o to t

o t

e se s

e s

h hh h

h h

sinsin

sin

g mg m

g m

unun

inin

g pg p

g p

. F. F

. F

il-il-

il-

urur

e te t

e t

o po p

o p

y ay a

y a

h ah a

h a

d td t

d t

n an a

n a

ll tll t

ll t

hrhr

e he h

e h

sinsin

sin

g ag a

g a

mbmb

y sy s

y s

s cs c

s c

ulul

d rd r

d r

ulul

t in tt in t

t in t

e se s

e s

h hh h

h h

sinsin

sin

g ag a

g a

d lid li

d li

urur

e fe f

e f

llinllin

llin

attaching the lower switch housing

1. Connect the upper plug connector from the motor to the lower

plug connector in the lower switch housing assembly. See Fig-

ure 24.

NOTE: Both plug connectors are polarized and will only fit to-

gether one way. Make sure that both connectors are properly

aligned before connecting them together. Incorrect connec-

tion could cause improper operation and damage to the prod-

uct.

urur

e 24 - Ce 24 - C

e 24 - C

nnnn

inin

g tg t

g t

e pe p

e p

lulu

g cg c

g c

nnnn

2. Place the lower switch housing assembly over the upper switch

housing. Align the side screw holes in the upper and lower

switch housings. Attach the lower switch housing to the up-

per switch housing with three #6-32 x 3/8" housing assembly

screws. See Figure 24.

installing accessory light fixtures

To install the light fixture, follow the instructions included with the

light fixture for wiring, mounting, and assembly.

Lower Plug

Connector

Upper Switch

Housing

Upper Plug

Connector

Lower

Switch

Housing

Assembly

Screw

Fan Pull

Chain

Reversing

Switch

operating your ceiling fan

1. Turn on electrical power to the fan.

2. The fan pull chain controls power to the fan. The pull chain

has four settings in sequence: High, Medium, Low and Off.

• Pull the chain slowly to change settings.

• Release slowly to prevent the chain from recoiling into the

blades.

• The chain uses a breakaway connector that separates if

the chain is jerked. If this happens, simply reinsert the chain

into the connector.

3. Ceiling fans work best by blowing air downward (counterclock-

wise blade rotation) in warm weather to cool the room with a

direct breeze. In winter, having the fan draw air upward (clock-

wise blade rotation) will distribute the warmer air trapped at

the ceiling around the room without causing a draft. Refer to

Figure 25.

urur

e 25 - Ae 25 - A

e 25 - A

ir fir f

ir f

w pw p

w p

To change the direction of air flow, turn the fan off and let it

come to a complete stop. Slide the reversing switch on the fan

to the opposite position as shown in Figure 26. Restart fan.

urur

e 26 - Pe 26 - P

e 26 - P

ull cull c

ull c

in ain a

in a

d rd r

d r

sinsin

sin

g sg s

g s