Hunter Fan 41844-01 Manual

Open as PDF

next previous

ll wll w

ll w

irir

inin

g mug mu

g mu

t bt b

t b

e in ae in a

e in a

e we w

e w

h nh n

h n

l al a

l a

d ld l

d l

l cl c

l c

s as a

s a

d Ad A

d A

I/NI/N

I/N

A 70. IA 70. I

A 70. I

f yf y

f y

u au a

u a

e une un

e un

iliili

ili

h wh w

h w

irir

inin

, y, y

, y

u su s

u s

ulul

d ud u

d u

e a qe a q

e a q

lili

d ed e

d e

urur

e 13 - We 13 - W

e 13 - W

irir

inin

g tg t

g t

e fe f

e f

installing the canopy

1. Rotate the fan 180º clockwise from the initial position when

hanging the fan. The arrows on the hanger ball and on the

ceiling plate should be pointing in the same direction and

should be pointing towards the tab hole on the canopy. Refer

to Figure 14.

urur

e 14 - Re 14 - R

e 14 - R

inin

g tg t

g t

e fe f

e f

2. Hook the tab hole over the tab on the ceiling plate as shown in

Figure 15.

3. Raise the canopy, be sure the holes in the canopy and the ceil-

ing plate are aligned, and loosely assemble the canopy screws

one at a time. When all three screws are assembled, securely

tighten all three canopy screws. Refer to Figure 15.

urur

e 15 - Ie 15 - I

e 15 - I

llinllin

llin

g tg t

g t

e ce c

e c

installing the canopy trim ring

1. To easily install the canopy trim ring, locate the two tabs on

the canopy trim ring. See Figure 16.

urur

e 16 - Ce 16 - C

e 16 - C

y ty t

y t

im rim r

im r

inin

2. Take both hands and push the canopy trim ring up to the top

of the canopy. See Figure 16.

3. The canopy trim ring will snap and lock into place on the

canopy.

removing the canopy trim ring

1. Locate the tab indicators, small bumps on top of tabs. Refer to

Figure 17.

2. To remove the canopy trim ring, press firmly on opposite sides

of the ring towards the canopy as shown in Figure 17. The tabs

will flex out releasing the trim ring from the canopy.

urur

e 17 - Re 17 - R

e 17 - R

inin

g tg t

g t

e ce c

e c

y ty t

y t

im rim r

im r

inin

Canopy

Trim Ring

Tab

Press Here when

Removing

Press Here when

Removing

Canopy Trim Ring

Canopy

Tab Indicator

Wall Switch Wire for Separate

Control of Light Fixture

(Note: Wall

switch must be

acceptable as a

general-use

switch.)

Power

Wires

Ceiling

Black

White

Bare or Green

2 x 4 Brace

Outlet Box

Ceiling Plate

Approved

Connectors

Green Ground Wire from

Hanger Pipe (not present

with flush mounting

option)

Connections:

1. Connect Blk/Wht

wire from the fan to the

wall switch for separate

control of the light

fixture, or

2. Connect Blk/Wht

wire from the fan to the

ceiling black wire if there

is no separate wall

switch wire for the light

fixture.

Blk/Wht

3 Wires

from Fan

White

Black

Tab Hole

and Tab

Canopy

Screw