Hunter Fan 41844-01 Manual

Open as PDF

next previous

4. Align the slotted holes (refer to Figure 9) in the ceiling plate

with the pilot holes in the wood support structure. Note: The

isolation pads should be flush against the ceiling.

For Angled Ceilings: Be sure to orient the ceiling plate so that

the arrows on the ceiling plate are pointing towards the ceiling

peak. Refer to Figure 9.

urur

e 9 - Le 9 - L

e 9 - L

inin

g tg t

g t

e se s

e s

d hd h

d h

s ts t

s t

o uo u

o u

5. Place a flat washer on each of the two 3" screws and pass the

screws through the slotted holes in the ceiling plate as shown

in Figure 10.

6. Tighten the screws into the 9/64" pilot holes; do not use lubri-

cants on the screws. Do not overtighten.

urur

e 10 - Ie 10 - I

e 10 - I

llinllin

llin

g tg t

g t

e ce c

e c

ilinilin

ilin

g pg p

g p

assembling the fan

assembling the fan for a standard or angled ceiling

1. Insert the downrod through the canopy and canopy trim ring

as shown in Figure 11. Feed wires from the fan through the

downrod.

2. Screw the downrod into the fan assembly until tight. IMPOR-

TANT! Tighten allen head set screw as shown in Figure 11 with

the included allen wrench.

N: TN: T

N: T

e de d

e d

nrnr

d hd h

d h

s a ss a s

s a s

l cl c

l c

inin

g og o

g o

n tn t

n t

hrhr

. D. D

. D

o no n

o n

t rt r

t r

e te t

e t

s cs c

s c

inin

g; tg; t

g; t

e ce c

e c

inin

g pg p

g p

e de d

e d

nrnr

d fd f

d f

m unm un

m un

inin

. O. O

. O

e ae a

e a

mbmb

d, dd, d

d, d

o no n

o n

e te t

e t

e de d

e d

nrnr

d.d.

3. Continue to the

inin

g tg t

g t

e fe f

e f

n section.

urur

e 11 - Ae 11 - A

e 11 - A

mbmb

linlin

lin

g tg t

g t

e de d

e d

nrnr

hanging the fan

1. Raise the fan and place the hook through the loop on the ceil-

ing plate as shown in Figure 12. Use the note and arrow en-

graved in the ceiling plate to assist in determining the direc-

tion to assemble.

G: FG: F

G: F

n mn m

n m

y fy f

y f

ll ill i

ll i

f nf n

f n

t at a

t a

mbmb

d ad a

d a

s dirs dir

s dir

d ind in

d in

e ine in

e in

llll

n inn in

n in

urur

e 12 - Hae 12 - Ha

e 12 - Ha

inin

g tg t

g t

e fe f

e f

wiring the fan

1. Disconnect the power by turning off the circuit breakers to

the outlet box and associated wall switch location.

2. You can use either one or two wall switches to control the fan

and/or lights separately. Use connection 1, as described in Fig-

ure 13, to

• control the light with a wall switch and the fan with a pull

chain (one wall switch required),

• control the light with a pull chain and the fan with a wall

switch (one wall switch required), or

• control the light with one wall switch and the fan with

another (two wall switches required).

Use connection 2, as described in Figure 13, if there is no sepa-

rate wall switch power wire for the light fixture.

NOTE: Wall switches not included.

3. Connect the wires as shown in Figure 13. To connect the wires,

twist the bare metal leads together. Place a wire nut over the

intertwined length of wire and twist clockwise until tight as.

N: BN: B

N: B

e se s

e s

urur

e ne n

e n

o bo b

o b

e we w

e w

irir

e oe o

e o

r wr w

r w

irir

e se s

e s

s as a

s a

e ve v

e v

ibib

e ae a

e a

r mr m

r m

inin

g cg c

g c

nnnn

Slots

Arrows for Orienting

on Angled Ceiling

Ceiling Joist

2 x 4 Brace

Ceiling

Ceiling Plate

Flat Washer

Outlet Box

3” Wood Screw

Hanger Ball/

Downrod Assembly

Canopy

Canopy Trim Ring

Allen Head Pipe Set Screw

Hook

Loop