Filter
Top Products
8
Enter the Heating Program
1) Press the Menu button and then press Set Schedule.
Press SYSTEM button to select either "Heat" or "Cool" in
the system switch area indicating the active mode being
programmed. You can switch to the other mode by
pressing the system switch at any time.
2) The top of the display will show the day(s) being pro-
grammed. The time and set at temperature are also
displayed. "Morning" will also be displayed to indicate
the period.
3) Press
or key to change the temperature to your
selected temperature for the 1st heating period (Morning).
4) Press
or key to adjust the start time for period.
The time will change in 15 minute increments.
5) Press FAN to select Auto or Prog.
6) After you have set the time and the temperature for the
period to begin, press Set Schedule to advance to the
next program period.
7) Repeat steps 2 through 6 until all of the program times
and temperatures are set for all program periods on
that day.
8) Press "Advance Day" to change to the next day and
repeat steps 2 through 8.
9) When programming is complete and all of the times and
temperatures match your desired heating schedule, press
Run Schedule. The thermostat will now run your program.
Enter the Cooling Program
1) Press the SYSTEM button until the Cool icon appears.
2) Follow Enter Heating Program instructions for entering
cooling times and temperatures.
PROGRAMMING
Fill in the blank schedule on the next page then:
Automatic Schedule
This feature provides a method to program every day with
the most popular time and temperature profile using one key
press. For this feature to be available, the Auto schedule
options (AS Cool or AS Heat) should be set on in the
installer configuration.
Select the desired “Comfort Temperature” in the setpoint.
When the Auto Schedule touch key is pressed, it will start
flashing indicating that it is now ready to insert the displayed
temperature setpoint as the “Comfort Temperature” for the
selected system mode currently in (Heat/Cool). A second
press of the Auto Schedule touch key will complete the
process. A 6
o
F setback temperature will also be inserted for
the night step. Once it is done, the touch key display Auto
Schedule will disappear disabling any further operation of
Auto Schedule touch key. If desired it can be enabled again
in the installer configuration menu.
Entering Fan Program
This key is used to select FAN Auto operation (fan energized
with a call for cool but not on with a call for heat) to FAN On
(fan on continuous) or FAN PROG (fan programmed to cycle
fixed time automatically). Each press of the FAN touch key
will change the mode from Auto to On to Prog. FAN Auto or
FAN On or FAN On Prog will display in the run mode for as
long as the fan is in that position. When FAN Prog position is
selected and the system key is in the Cool, Heat or Auto
mode the circulator blower (fan) will cycle ON for 10 minutes,
OFF for 20 minutes when the thermostat has not called for
cooling or heating for the past 60 minutes.
To improve indoor air quality, the system circulator can be
programmed to run during any program time period by
touching the Fan touch key in the appropriate program time
period when in the Menu mode for that particular day.
The display shall indicate Prog (under the Fan icon) when in
Menu mode and the fan is programmed to come on during
that time.
In the menu mode, each time the fan key is pressed, the fan
operation and display will change from FAN Auto to FAN
Prog. The display shall indicate FAN On Prog when in run
mode and the fan is programmed to run for that particular
time period.
When in Run Schedule mode and the FAN touch key is
pressed, it will override the schedule, and the display and fan
operation shall change to FAN Auto and the fan is stopped.
Further key depression will change it to FAN On (continuous
blower on) and to FAN Prog (cycling 10 minutes on and 20
minutes off if there is no call for heat or cool for 60 minutes).
The Run Schedule touch key will also be indicated, meaning
that it is an override on the scheduled program. The override
will last until next schedule comes up or the Run Schedule
touch key is depressed.