Filter
Top Products
8
Starting your air conditioner
Operating your air conditioner properly helps you to obtain the best possible results.
This section explains proper air conditioner operation.
IMPORTANT:
• If you turn the air conditioner off and then turn the unit back on, the fan will come on, but the compressor will remain off
for 3 minutes before turning back on. This prevents the air conditioner from blowing a fuse or tripping a circuit breaker.
• Do not try to operate your air conditioner in the cooling mode when outside temperature is below 65°F (18°C). The
inside evaporator coil will freeze up, and the air conditioner will not operate properly.
Press Power ON/OFF to turn on air
conditioner. When the unit is turned on, it will
display the previous settings for the MODE,
FAN SPEED and temperature.
FAN SPEED SELECTION
NOTE: FAN SPEED button will operate only
when COOL or POWER SAVER mode has
been selected.
Press FAN SPEED until you see the indicator
light for the setting you want. Choose TURBO,
HIGH or LOW.
TIMER DELAY
The TIMER can be set for a 1 to 24 hour
delay until the air conditioner turns on or off.
Press
▲
or
▼
to adjust the delay time.
To set the TIMER delay to turn the air
conditioner off, air conditioner must be in the
ON mode.
Press TIMER. (Indicator light will flash.)
Press
▲
or
▼
to change delay time (1 to 24
hours).
Press TIMER or wait 10 seconds. (Indicator light will
remain on.)
To set the TIMER delay to turn the air conditioner on, air
conditioner must be in the OFF mode.
If you want to change the previous settings:
Turn air conditioner on.
Adjust MODE to AUTO, COOL, FAN, or POWER SAVER.
Adjust FAN SPEED to TURBO, HIGH or LOW.
Adjust TEMPERATURE between 64°F (18°C) and 86°F
(30°C).
Turn air conditioner off.
Press TIMER. (Indicator light will flash.)
Press
▲
or
▼
to change delay time (1 to 24 hours).
Press TIMER or wait 10 seconds.
If you want to keep the previous settings:
Turn air conditioner off.
Press TIMER. (Indicator light will flash.)
Press
▲
or
▼
to change delay time (1 to 24 hours).
Press TIMER or wait 10 seconds.
To clear TIMER delay program, press and hold TIMER for
3 seconds. Indicator light will shut off. Air conditioner can
be either on or off.
To see the remaining time (in hours), press TIMER once
after it has been programmed. While the display is
showing the remaining time, you can press
▲
or
▼
to
increase or decrease the time.
Air Conditioner Use
EN
TEMPERATURE SELECTION
Press
▲
to raise the temperature.
Each time you press or hold
▲
, the
temperature will go up 1° until it
reaches 86°F (30°C).
Press
▼
to lower the temperature.
Each time you press or hold
▼
, the temperature will go
down 1° until it reaches 64°F (18°C).
MODE SELECTION
Press MODE until you see the indicator light
come on for the setting you want. Choose
AUTO, COOL, FAN or POWER SAVER.
AUTO – Cools room while it automatically
controls fan speed. You cannot change fan
speed, but you can adjust temperature by
pressing
▲
or
▼
.
COOL – Cools room. You can select fan speed by
pressing FAN SPEED. You can then adjust temperature
by pressing
▲
or
▼
.
FAN – Fan runs on TURBO speed only. Only the fan
runs. Display shows “FO” (fan only).
POWER SAVER – Fan and compressor run only when
cooling is needed. Fan stops running when the room
temperature matches the temperature you set.
Press FAN SPEED until you see the indicator light for
the setting you want. Choose TURBO, HIGH
or LOW.
Select the temperature by pressing
▲
or
▼
.
ADJUST
TIMER